Crestron 302 Instrukcja instalacji
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Kontroler Crestron 302. Crestron 302 2 stron. 3 series media presentation controller
Drukuj stronę
DO
GUIDE
MPC3-302
3-Series
Media Presentation Controller 302
®
DO
Attach the Mounting Plate
The Crestron
®
MPC3-302 3-Series
®
media presentation controller installs
into a 3-gang U.S. electrical box.
NOTE:
The MPC3-302 may also be installed onto a tabletop or other flat
surface using the TTK-MP/MPC/IPAC tabletop kit and the optional
SMK-MP/MPC/IPAC swivel mount kit. For more information and installation
instructions, refer to the TTK/MP/MPC/IPAC & SMK-MP/MPC/IPAC
Installation Guide (Doc. 6782) at www.crestron.com/manuals.
Use the four 6-32 x 1" screws to attach the MPC3-302 mounting plate to the
electrical box. Ensure that the mounting plate is level and flush against the
electrical box after installation.
DO
Connect the Device
Route all necessary cables through the rear of the electrical box, and then
make connections to the MPC3-302 as shown in accompanying illustration.
NOTE:
All cable connections must be made prior to attaching the
MPC3-302 assembly to the electrical box.
Observe the following when connecting the MPC3-302:
•
Use Crestron power supplies for Crestron equipment.
•
Power is supplied to the MPC3-302 over a single Ethernet cable.
A PoE+ (Power over Ethernet) power supply or a network switch
capable of PoE+ is recommended (both sold separately).
•
The MPC3-302 must use PoE+ to supply power to a
Cresnet
network device via the NET connector.
®
•
Ensure that the device is properly grounded by connecting the
chassis ground lug to an earth ground (building steel).
•
Apply power after all connections have been made.
Drywall
3-gang U.S.
surface
electrical box
Mounting
plate
Screw (4):
6-32 x 1"
NET:
LAN PoE:
To any Cresnet
10BASE-T / 100BASE-TX
network device
Ethernet to LAN
LAN PoE
I/O
RELAY:
To controllable
devices
IR:
COM:
I/O:
To IRP2 emitter
To any
To digital or
or serial devices
RS-232 device
analog devices
DO
Check the Box
QUANTITY
1
Bit, Torx
®
, T8, Security
1
Plate, Metal, Mounting, 6.5" x 4.3" x 1.5"
6
Screw, 4-20 x 3/4", Pan Head, Phillips, Thread Forming
6
Screw, 4-40 x 1/4", Pan Head, Phillips
4
Screw, 6-32 x 1", Pan Head, Phillips
1
Screw, Security, Torx
MPC3-302-B Only
10
Button Cap, Black
1
Button Cap, Mute, Black
1
Button Cap, Power, Black
1
Cover, Black
1
Labels, Sources, 30 Piece Set, Black
MPC3-302-W Only
10
Button Cap, White
1
Button Cap, Mute, White
1
Button Cap, Power, White
1
Cover, White
1
Labels, Sources, 30 Piece Set, White
DO
Complete the Installation
1.
Once all connections have been made, use the six 4-40 x 1/4" screws to attach the MPC3-302 assembly to the mounting plate.
NOTE:
The six 4-20 x 3/4" screws are used to attach the MPC3-302 assembly to the TTK-MP/MPC/IPAC enclosure. For more information, refer to
the TTK/MP/MPC/IPAC & SMK-MP/MPC/IPAC Installation Guide (Doc. 6782).
Ground
Screw (6):
4-40 x 1/4"
ITEM
Mounting
plate
MPC3-302
assembly
PART NUMBER
2025915
2049785
2007140
2007156
2007251
2051148
2049780
2049784
2049782
4527101
4527386
2049779
4527719
4527718
4527100
4527385