Shimano FC-CX70 Techniczne instrukcje serwisowe - Strona 2
Przeglądaj online lub pobierz pdf Techniczne instrukcje serwisowe dla Akcesoria rowerowe Shimano FC-CX70. Shimano FC-CX70 2 stron. Front chainwheel
Drukuj stronę
SI-1MR0A-001-00
General Safety Information
WARNING
"Maintenance interval depends on the usage and riding circumstances. Clean
regularly the chain with an appropriate chaincleaner. Never use alkali based or
acid based solvents such as rust cleaners. If those solvent be used chain
might break and cause serious injury."
• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise you may
fall off the bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is too
weak or the chain is damaged, the chain should be replaced. If this is not done, the chain may break
and you may fall off the bicycle.
• The two left crank arm mounting bolts should be tightened alternately in stages rather than each bolt
being fully tightened all at once. Use a torque wrench to check that the final tightening torques are
within the range of 12 - 14 N·m. Furthermore, after riding approximately 100 km (60 miles), use a
torque wrench to re-check the tightening torques. It is also important to periodically check the
tightening torques. If the tightening torques are too weak or if the mounting bolts are not tightened
alternately in stages, the left crank arm may come off and the bicycle may fall over, and serious injury
may occur as a result.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the
crank arm may break and you may fall off the bicycle.
• If the inner cover is not installed correctly, the axle may rust and become damaged, and the bicycle
may fall over and serious injury may occur as a result.
• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or
damaged parts may cause the bicycle to fall over and serious injury may occur as a result. We
strongly recommend only using genuine Shimano replacement parts.
• Obtain and read the service instructions carefully prior to installing the parts. If adjustments are
not carried out correctly, the chain may come off and this may cause you to fall off the bicycle which
could result in serious injury.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
CAUTION
• If the chain is on the smallest or intermediate chainring, there is the danger of injury from the tips of
the teeth on the largest chainring.
Note
• Make sure that the chainring combination matches the front chainwheel tooth configuration in the
Product specifications table. If other combinations are used, the distance between the chainrings will
be incorrect and the chain might slip off and get caught in between them.
• When the chain is in the position shown in the illustration, the chain may
contact the front chainrings or front derailleur and generate noise. If the noise is
a problem, shift the chain onto the next-larger rear sprocket or the one after.
• If the bottom bracket shell is not parallel, gear shifting performance will drop.
• Before riding the bicycle, check that there is no play or looseness in the connection.
Also, be sure to retighten the crank arms and pedals at periodic intervals.
• If a squeaking noise is heard coming from the bottom bracket axle and the left
crank arm connector, apply grease to the connector and then tighten it to the specified torque.
• Use a neutral detergent to clean the crank arm and the bottom bracket. Using alkaline or acidic
detergents may cause discoloration.
• If you feel any looseness in the bearings, the bottom bracket should be replaced.
• In addition, if pedaling performance does not feel normal, check this once more.
• Do not wash the bottom bracket with high-pressure jets of water.
• When installing the left and right adapters, be sure to install the inner cover too, otherwise the
waterproofing performance will drop.
• Apply grease to the left and right adapters before installing them.
• To ensure the best performance, be sure to use only the specified type of chain. The wide type of
chain cannot be used.
• If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.
• You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In
addition, cleaning the chain with neutral detergent and lubricating it can be an effective way of
extending the useful life of the chainrings and the chain.
• The cuffs of your clothing may get dirty from the chain while riding.
• When installing the pedals, apply a small amount of grease to the threads to prevent the pedals from
sticking. Use a torque wrench to securely tighten the pedals. Tightening torque: 35 - 55 N·m {305 - 479
in. lbs.}. The right-hand crank arm has a right-hand thread, and the left-hand crank arm has a left-hand
thread.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For maximum performance we highly recommend Shimano lubricants and maintenance products.
• For any questions regarding methods of installation, adjustment, maintenance or operation, please
contact a professional bicycle dealer.
Technical Service Instructions
FC-CX70 / FC-CX50
Front chainwheel
Specifications
Model number
Chainwheel tooth combination
Bolt circle diameter
Pedal threads
Applicable chain
Chain line
Bottom bracket shell width
(Thread dimensions)
Bottom bracket
Installation of the front chainwheel
Follow the procedure in the figure.
1. 2.
Use the TL-FC32/33/36 special tool to install the right
Front
adapter (counterclockwise thread), the inner cover and
chainrings
the left adapter (clockwise thread).
Tightening torque: 35 - 50 N·m {305 - 435 in. lbs.}
Rear
3.
sprockets
Insert the right crank unit.
4.
Set section A of the left crank into the axle of the right
crank unit where the groove is wide.
5.
Use the TL-FC16/18 to tighten the cap.
Tightening torque: 0.7 - 1.5 N·m {6 - 13 in. lbs.}
6.
Push in the stopper plate and check that the plate pin is
securely in place, and then tighten the bolt of the left
crank arm. (5 mm Allen key)
Note :
Each of the bolts should be evenly and equally
tightened to 12 - 14 N·m {106 - 122 in. lbs.}.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
* Service Instructions in further languages are available at : http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English) © Feb. 2011 by Shimano Inc. XBC IZM Printed in Malaysia.
SI-1MR0A-001
Installation of the chainrings
• Smooth shifting will not be possible if the chainrings are incorrectly
installed, so be sure to install the chainrings in the correct positions.
With the marked surface of
the larger chainring facing
out, set the larger chainring
so that the chain drop
prevention pin is lined up
with the crank arm position.
FC-CX70
FC-CX50
46 G – 36 G
110 mm
B.C. 9/16" x 20 T.P.I. (English thread)
CN-7901 / 6701
CN-5701 / 4601
With the marked surface of the smaller
chainring facing away from the crank arm, set
43.5 mm
the chainring so that the projection on the
68 mm (1.37 x 24 T.P.I.)
inside is aligned with the crank arm.
70 mm (M36 x 24 T.P.I.)
SM-BB6700
SM-BB4600
Tightening torque:
< FC-CX70 >
12 - 16 N·m {106 - 139 in. lbs.}
< FC-CX50 >
12 - 14 N·m {106 - 122 in. lbs.}
(A)
TL-FC16
5
Plate pin
Stopper plate
Push up
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Outer side
Crank arm
Chain drop prevention pin
Inner side
Mark
Projection
Crank arm
• Right adapter
4
clockwise thread for 70 mm
TL-FC32
[M36] bottom brackets
Wide groove area
2
6
1
Inner cover
Bottom bracket shell
Note :
Set the stopper plate in the right
direction as shown in illustration.
3