Siemens Sivacon S8 Instrukcja obsługi - Strona 19

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Urządzenia przemysłowe Siemens Sivacon S8. Siemens Sivacon S8 24 stron. Switchboard
Również dla Siemens Sivacon S8: Instrukcja obsługi (7 strony), Instrukcja obsługi (24 strony), Podręcznik (11 strony), Instrukcja obsługi (11 strony), Instrukcja obsługi (19 strony), Instrukcja obsługi (12 strony), Instrukcja obsługi (29 strony), Instrukcja obsługi (13 strony), Instrukcja obsługi (13 strony), Instrukcja obsługi (11 strony), Instrukcja obsługi (9 strony), Instrukcja obsługi (15 strony), Podręcznik (11 strony), Instrukcja obsługi (9 strony), Dokumentacja naprawy (44 strony), Instrukcja obsługi (12 strony), Instrukcja obsługi (11 strony), Instrukcja obsługi (18 strony)

No caso dos interruptores fixos embutidos, as câmaras de arco vol-

taico podem ser checadas graças à altura de compartimento

adequada. Depois de soltas, as câmaras (ver instruções de serviço

3W...) podem ser levantadas, giradas para o lado e retiradas do com-

partimento pela frente.

Introdução/remoção do disjuntor mediante a mesa elevatória:

Introdução/remoção do disjuntor 3W mediante empilhadeira manual

(adequada para 3W até 6300A) e placa de suporte com calhas adicio-

nais.

Fig. 17 / Fig. 137

Montar as calhas adicionais do carro elevador, de modo a que fi-

quem posicionadas entre as calhas telescópicas da gaveta e man-

tenham uma distância de apoio tão ampla quanto possível (figura

17).

Orientar a plataforma do carro elevador com as calhas adicionais sob o

interruptor que foi retirado para a posição de manutenção. As calhas adi-

cionais devem ficar aproximadamente centradas sob o interruptor (figura

18).

Cuidado

Orientar as calhas adicionais de forma a que assentem sobre a

base do interruptor, atrás do console de comando em plástico.

Para que o console de comando não seja danificado ao elevar o

interruptor, a empilhadeira manual deverá ser aproximada do

quadro, à distância adequada!

8PQ9800-8AA51

On fixed-mounted circuit breakers, the compartment is high enough to

inspect the arc chutes. The chutes can be detached (see operating in-

structions for 3W...) and lifted, swung to the side, and removed through

the front of the compartment.

Inserting/removing the circuit breaker using a lifting table:

Fig. 16 / Fig. 16

Insertion and removal of the 3W circuit breaker using a lifting truck (suit-

able for 3W up to 6300A) and carrying plate with additional rails

Fig. 18 / Fig. 18

Mount the additional bars of the lifting truck so that they provide support

between the telescopic guide support of the guide frame but are as far

apart as possible (Fig. 17).

Align the lifting truck platform with the additional bars below the circuit

breaker, which has been pulled out into the maintenance position. The

additional rails should be positioned approximately centrally under the

circuit breaker (Fig.18).

CAUTION

Align the additional bars so that they are located on the base of the

circuit breaker behind the plastic control panel.

Move the lifting truck close enough to the cubicle so that the control

panel is not damaged when the circuit breaker is lifted!