Samsung 403 Series Podręcznik szybkiej konfiguracji
Przeglądaj online lub pobierz pdf Podręcznik szybkiej konfiguracji dla Monitor Samsung 403 Series. Samsung 403 Series 2 stron. 4 series; 5 series
Również dla Samsung 403 Series: Podręcznik użytkownika (35 strony), Podręcznik użytkownika (35 strony), Podręcznik użytkownika (49 strony), Podręcznik użytkownika (32 strony), E-podręcznik (32 strony)
Drukuj stronę
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
STOP
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
Please do not return this unit.
85 Challenger Road Ridgefi eld Park, NJ 07660-2112
If you have problems operating your
Samsung Electronics Canada Inc.
TV, call:
1-800-SAMSUNG (1-800-726-7864)
55 Standish Court Mississauga, Ontario L5R 4B2
For web support please visit:
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
www.samsung.com/support
To register this product, visit : www.samsung.com/register.
Getting Started
Step 1 :
Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.
Lift the cover on the back of the remote upward
as shown in the fi gure to the right.
2.
Install two AAA batteries.
Make sure to match the + and - ends of
the batteries to the diagram in the battery
compartment.
Replace the cover.
3.
Step 2 :
Connect Power and Antenna or Cable
Connect ANT IN to:
• Wall cable jack or
• VHF/UHF
or
Antenna or
• Cable or Satellite
box Ant or Cable
Power Input
Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is
plugged in securely to the wall
outlet and the TV.
Step 3 :
Connect External Devices
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note
that many digital cable programs are not in HD. Check with your video provider to ensure your devices are
receiving HD signals.
AV IN 2
Audio/Video connection (480i only)
Using an Audio/Video Cable
VIDEO OUT
AUDIO OUT
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Lowest Quality Connection
Step 4 :
Run Plug & Play
When you turn on your TV for the fi rst time, it automatically launches
the Plug & Play function. With Plug & Play, you can select the On
Screen Display language, set the clock mode, and launch the TV's
channel memorizing process. It also displays connection instructions
similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or
Right arrow buttons on your remote. To make a selection, press the
ENTERE
button. To skip a screen, press the
MENU
button.
To turn on your TV, press the
POWER
button on the remote or press
the
POWER
button on the TV. To run Plug & Play, follow these steps:
Plug & Play
Select Language of the OSD.
English
1
Español
Language
: English
Français
U Move E Enter
On the Language screen, select the language for the On Screen
Display (OSD) using your remote control, and then press
ENTERE
button. The Home Use screen appears.
Plug & Play
Select 'Home Use' when installing this TV in your home.
2
Store Demo
Home Use
L Move E Enter
Select Home Use, and then press
ENTERE
button. If you select
Store Demo, the TV will reset your picture and audio settings every
30 minutes. After you press
button , the Antenna Source
ENTERE
screen appears.
The HDMI connection carries
digital video and audio.
VCR
Plug & Play
Select the Antenna source to memorise.
3
Air
Start
Cable
Start
Auto
Start
U Move E Enter m Skip
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your
TV is attached to an antenna and cable with no box, select Auto.
When done, press
ENTERE
button on your remote. The Select
Cable System screen appears.
IMPORTANT:
If your TV is attached to a cable or satellite box,
skip Steps 3 through 5. After Plug & Play is complete, set your TV to
Channel 3 or 4, according to the directions for your cable or satellite box.
Plug & Play
Selects the cable system.
Analog
STD
HRC
IRC
4
Digital
STD
HRC
IRC
Start
U Move E Enter m Skip
If your TV is attached to a cable system and you have no cable box,
you must select your cable system type. If you have Digital cable, you
must select the cable system type for both Analog and Digital.
After you have selected the cable system type, select Start, and then
press the
ENTERE
button on your remote.
Most cable systems are Standard (STD) systems. If you are not
sure about what kind of cable system you have, contact your
cable company.
English - 1
AV IN 2
AV IN 2
HD connection (up to 1080p)
Using an HDMI Cable
Device
HDMI OUT
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
AV IN 2
AV IN 2
Best Connection
HD connection (up to 1080p)
Using an DVI to HDMI Cable
DVI OUT
Device
AV IN 2
DVD / Blu-Ray player /
Cable Box /
Satellite receiver (STB)
Very Good Connection
Component connection (up to 1080p)
Using a Component Cable
Blu-ray player
AUDIO OUT
COMPONENT OUT
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Good Connection
Plug & Play
Auto Program in Progress.
5
DTV Cable : --
Cable : --
Cable
28
15%
Stop
E Enter m Skip
The TV memorizes the available channels. This process can take
up to 45 minutes.
Plug & Play
Set the Clock Mode.
6
Auto
Clock Mode
: English
Manual
U Move E Enter m Skip
After the TV has memorized the channels, choose the Clock
Mode. Select Auto if you have a digital channel in your area. Select
Manual if you don't, or if you have a cable or satellite box. When
done, press
ENTERE
button.
If you select Manual, the clock setting screen appears.
Plug & Play
Set to daylight saving time.
Off
7
DST
On
: English
Auto
U Move E Enter m Skip
Select the daylight savings time setting: Off, On, or Auto, and then
press
button.
ENTERE
After the time zone screen,
The connection method
for best HD screen quality
is displayed. Press Right
8
arrow button on your
remote to view each screen
in succession. Press the
MENU
button to skip this
section.
The Enjoy your TV screen
9
appears. Then press
ENTERE
button.