A
djust the image
1
Rotate the focus ring to sharpen the image.
Focus adjustment
Image size adjustment
Note:
If you see a blank screen
the instructions to the right.
2
Rotate the zoom ring to reduce or enlarge the image. Turn to
W (wide) to enlarge or T (tele) to reduce. (You can also move
the projector closer to or farther from the screen.)
3
To raise the image, press the blue foot release levers inward
and lift the front of the projector. Once the image is positioned
where you want it, release the levers to lock the feet in position.
4
If your image looks like
off to one side of the screen, at an angle. Move it directly in
front of the center of the screen, facing the screen squarely.
5
If your image looks like
feature has been disabled. You can manually adjust the keystone
correction value by pressing the
button on the projector. Or, to enable Auto Keystone correction,
refer to your User's Guide.
W
here to get help
Telephone Support Services
To use the EPSON PrivateLine
and enter the PIN on the EPSON PrivateLine Support card included in
your owner's kit. This service is available 6
Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing
one of these numbers:
U.S.:
(562) 276-4394, 6
AM
Monday through Friday
Canada: (905) 709-3839, 6
AM
Monday through Friday
Toll or long distance charges may apply.
Electronic Support Services
EPSON provides technical assistance through electronic support
services 24 hours a day at http://support.epson.com. For tips,
templates, and training for developing successful presentations
go to http://www.presentersonline.com.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
EPSON disclaims any and all rights in those marks. Copyright © 2002 by Epson America, Inc. Printed in Japan. 5/02
after focusing, see
No signal (
?
Help)
or
, you've placed the projector
or
, the Auto Keystone correction
or
side of the Keystone
®
Support service, call (800) 637-7661
to 6
, Pacific Time,
AM
PM
to 6
, Pacific Time,
PM
to 6
, Pacific Time,
PM
EPSON
PowerLite
®
If you see a blank screen
If you see a blank screen or the No signal message
after turning on your laptop, check the following:
Make sure the
power light is green and
not flashing and the lens cover is off.
Try turning off the laptop and restarting it.
If you've connected more than one computer and/or video source,
you may need to press the Source button on top of the projector.
(Allow a few seconds for the projector to sync up after pressing it.)
If you're using a Windows laptop:
Hold down the Fn button and press the function key that lets you
display on an external monitor. It may have an icon such as
or it may be labelled CRT/LCD. Allow a few seconds for the projector
to sync up after pressing it.
On most systems, the
screen and the projector, or display on both at the same time.
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
Check your laptop's manual or online help for details.
If you're using a Macintosh
1. From the Apple
®
menu, select Control Panels, then click Monitors
or Monitors and Sound.
2. Click the Arrange icon.
Click here
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
If the Arrange option isn't available, you may need to select
one of the Simulscan resolution settings:
4. Click the Monitor icon.
Click here
5. Select a Simulscan resolution as shown. (Allow a few seconds for
the projector to sync up after making the selection.)
Quick Setup
720c/730c
®
No signal (
key lets you toggle between the LCD
®
:
Drag one monitor icon
on top of the other
Select a Simulscan
resolution
CPD-13916R1
Help )
?
,
Drukuj stronę