Epson 755c - PowerLite XGA LCD Projector Instrukcja obsługi - Strona 38

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Projektor Epson 755c - PowerLite XGA LCD Projector. Epson 755c - PowerLite XGA LCD Projector 47 stron. Release of check tool for network projectors v1.00 for windows
Również dla Epson 755c - PowerLite XGA LCD Projector: Podręcznik użytkownika (42 strony), Instrukcja obsługi (36 strony), Arkusz specyfikacji (2 strony), Instrukcja obsługi (26 strony), Biuletyn wsparcia produktu (30 strony), Elementy wymieniane przez użytkownika (1 strony), Szybka konfiguracja (2 strony), Instrukcja instalacji (19 strony), Podręcznik użytkownika (1 strony), Podręcznik funkcji (5 strony), Biuletyn wsparcia produktu (25 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (12 strony), Biuletyn wsparcia produktu (42 strony), Biuletyn wsparcia produktu (22 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (41 strony), Biuletyn wsparcia produktu (34 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (15 strony), Biuletyn wsparcia produktu (22 strony)

Drukuj stronę

Epson 755c - PowerLite XGA LCD Projector Instrukcja obsługi

Mail notification function settings

The mail notification function can be used to send corresponding

notification messages to a preset e-mail address when a projector that is

connected to the network assumes a certain status, or if it experiences a

problem or warning. By using this function, the operator can be notified

of a projector's status or problems even when the operator is in a

different location from the projectors.

• Up to three addressees (destinations) can be registered and messages can be

sent to all of them at once.

• If a critical problem develops with a projector which causes it to suddenly

stop working, it may not be possible for the projector to send a message

notifying an operator of the problem.

• If Standby Mode is set to Communication On (or Network On) or Network

Monitoring is set to On in the projector configuration menus, you can

monitor the projector even when it is in standby mode (when its power is

turned off). s Projector's User's Guide

• On some projectors, the mail notification function can be set in the

configuration menu. When notification messages are set to be sent in the

projector's configuration menu, both the settings in the configuration menu

and settings made on EasyMP Monitor are functional.

• Detectable status with the mail notification function differs depending on

the projector you are using.

Procedure

Select "Mail notification function" from the Tool menu.

The Set mail notification function window will be displayed.

Make the necessary settings while referring to the table below.

Mail notification

Set to On to use the mail notification function.

function

SMTP server IP

Enter the IP address of the SMTP server. Up to

address

a maximum of 255 bytes can be entered.

When you change a port number of the SMTP

server, specify this port number. The default

value is "25".

You can enter a valid number from 1 to 65535.

Sender mail

Enter the sender's e-mail address. Up to a

address

maximum of 255 bytes can be entered.

Recipient mail

Specify the destination addresses for the

address 1

notification e-mail. Up to three destinations

can be set. Up to a maximum of 255 bytes can

Recipient mail

be entered.

address 2

Recipient mail

address 3