Epson 835p - PowerLite XGA LCD Projector Instrukcja obsługi - Strona 31

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Projektor Epson 835p - PowerLite XGA LCD Projector. Epson 835p - PowerLite XGA LCD Projector 36 stron. Release of check tool for network projectors v1.00 for windows
Również dla Epson 835p - PowerLite XGA LCD Projector: Podręcznik użytkownika (42 strony), Szybka konfiguracja (4 strony), Instrukcja obsługi (47 strony), Biuletyn wsparcia produktu (30 strony), Podręcznik uzupełniający (1 strony), Broszura i specyfikacje (4 strony), Informacje o produkcie (21 strony), Instrukcja instalacji (19 strony), Podręcznik użytkownika (1 strony), Streszczenie techniczne (7 strony), Podręcznik funkcji (5 strony), Biuletyn wsparcia produktu (25 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (12 strony), Biuletyn wsparcia produktu (42 strony), Biuletyn wsparcia produktu (22 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (41 strony), Biuletyn wsparcia produktu (34 strony), Biuletyn wsparcia produktu (38 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (15 strony), Biuletyn wsparcia produktu (22 strony), Arkusz specyfikacji (4 strony)

Drukuj stronę

Epson 835p - PowerLite XGA LCD Projector Instrukcja obsługi

Setting the mail notification function

The mail notification function can be used to send corresponding notification

messages to a preset e-mail address when a projector that is connected to the

network assumes a certain status, or if it experiences a problem or warning. By

using this function, the operator can be notified of a projector's status or

problems even when the operator is in a different location from the projectors.

TIP

• Up to three addressees (destinations) can be registered and

messages can be sent to all of them at once.

• If a critical problem develops with a projector which causes it to

suddenly stop working, it may not be possible for the projector to

send a message notifying an operator of the problem.

• If "Standby Mode" is set to "Network ON" or "Network

Monitoring" is set to "ON" in the projector configuration menus,

you can monitor the projector even when it is in standby mode

(when its power is turned off). See your User's Guide for more

information.

• On some projectors, the mail notification function can be set in the

configuration menu. When notification messages are set to be sent

in the projector's configuration menu, both the settings in the

configuration menu and settings made on EMP Monitor are

functional.

• Detectable status with the mail notification function differs with the

projector you are using.

PROCEDURE

Select "Mail notification function" from the "Tool"

menu.

The "Set mail notification function" window will be

displayed.

Set the following parameters.

Mail notification

Set to "ON" to use the mail notification function.

function

SMTP server

Enter the IP address of the SMTP server.

IP address

Up to a maximum of 255 bytes can be entered.

When you change a port number of the SMTP

server, specify this port number. The default value

is "25".

You can enter a valid number from 1 to 65535.

Sender mail

Enter the sender's e-mail address. Up to a

address

maximum of 255 bytes can be entered.

Recipient

mail address 1

Specify the destination addresses for the

Recipient

notification e-mail. Up to three destinations can be

mail address 2

set. Up to a maximum of 255 bytes can be entered.

Recipient

mail address 3