Siemens Washing machine Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Spryskiwacz Siemens Washing machine. Siemens Washing machine 6 stron. Washing machine
Również dla Siemens Washing machine: Instrukcja instalacji i konserwacji (10 strony), Instrukcja obsługi (8 strony), Instrukcja instalacji (6 strony), Instrukcja obsługi i instrukcja instalacji (28 strony), Skrócona instrukcja obsługi (2 strony), Skrócona instrukcja obsługi (2 strony), Skrócona instrukcja obsługi (2 strony), Instrukcja obsługi i instrukcja instalacji (28 strony), Instrukcja obsługi (28 strony), Instrukcja obsługi (10 strony), Skrócona instrukcja obsługi (2 strony), Instrukcja obsługi (10 strony), Instrukcja obsługi (28 strony), Instrukcja obsługi (10 strony)

Drukuj stronę
Siemens Washing machine Instrukcja instalacji
Alignment
Intense noise formation, vibrations and "wandering" may be the result of incorrect
alignment.
Aligning the washing machine with a spirit level
1. Loosen the lock nut using a wrench, by turning it in a clockwise direction.
2. Change the height by turning the appliance feet.
Caution: all four appliance feet must be firmly on the ground.
The washing machine must not wobble.
Check the alignment of the washing machine with a spirit level and adjust
if necessary.
3. Tighten the lock nut against the housing.
In doing so, hold the foot tight and do not adjust its height.
Caution: the lock nuts on all four appliance feet must be screwed tightly
against the housing.

Electrical connection

The washing machine must only be connected to an alternating current via a
properly installed earthed socket.
The power supply and voltage indicated on the washing machine (rating plate)
must be the same.
The connected load and fuse required are specified on the rating plate.
Make sure that:
– the mains plug fits the socket,
– the cable cross-section is adequate,
– the earthing system is properly installed.
(If this is necessary), the mains cable may only be replaced by a qualified
electrician.
Replacement mains cables are available from the after-sales service.
Do not use multiple plugs/couplings or extension cables.
If a residual current circuit breaker is used, only use a type which displays this
symbol: ‚.
Only this symbol guarantees compliance with the currently applicable regulations.
Do not plug in or unplug the mains plug with wet hands.
Pull the appliance plug out of the socket at the plug only, not by the cable.
Manufacturer –> Operating instructions
Transportation, e.g. when moving home
1.
Before transporting the washing machine:
1. Turn off the tap.
2. Drain residual water
Operating instructions; Maintenance - drain pump.
3. Release the water pressure in the inlet hose
in water inlet.
4. Disconnect the washing machine from the power supply.
5. Dismantle the hoses.
2.
Preparing and installing transport braces:
1.
Remove all covers and store them.
2.
Affix all transport braces. In doing so, turn the
bend on the hose holders inwards. Clamp the
mains cable in the holders. Tighten the screws.
After transportation, the transport braces must be removed.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour
2 litres of water into compartment II and start the Empty programme.

Technical specifications

Dimensions (width x depth x height)
Weight
Mains connection
Water pressure
5
Operating instructions; Maintenance - filter
page 3.
60 x 55 x 85 cm
66 – 73 kg depending on model
Nominal voltage 220-240 V, 50 Hz
Nominal current 10 A
Nominal power 2,300 W
200-1000 kPa (2-10 bar)
6