Siemens EC615PB90E Instrukcja montażu - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja montażu dla Hob Siemens EC615PB90E. Siemens EC615PB90E 21 stron.

Drukuj stronę

Read the appliance's instructions before

installing and using.

The graphics in these Assembly

instructions are given as a guide only.

The manufacturer is exempt from all

liability if this manual's requirements

are not complied with.

Safety instructions

All installation, regulation and

adaptation to other types of gas must

be carried out by an authorised

installation technician, respecting all

applicable regulations, standards

and the country's electrical and gas

supply companies' specifications.

It is recommended that you call our

Technical Assistance Service for

adaptation to other types of gas.

Before you begin, turn off the

appliance's electricity and gas

supply.

This appliance has been designed for

home use only, not for commercial or

professional use. This appliance cannot

be installed on yachts or in caravans.

The warranty will only be valid if the

appliance is used for the purpose for

which it was designed.

Before installing, you need to check that

local distribution conditions (gas type

and pressure) and the appliance's

adjustment are compatible (see table I).

The appliance's adjustment conditions

are written on the label or the

specifications plate.

This appliance can only be installed in a

well-ventilated place in accordance with

existing regulations and ventilation

specifications. The appliance must not

be connected to a combustion product

evacuation device.

The supply cable must be attached to

the unit to prevent it from touching hot

parts of the oven or hob.

Appliances with electrical supply must

be earthed.

Do not tamper with the appliance's

interior. If necessary, call our Technical

Assistance Service.

Before installing

This appliance is class 3 type, according

to the EN 30-1-1 regulation for gas

appliances: built-in appliance.

The units next to the appliance must be

made of non-flammable materials. The

laminated covering and glue for

adhering it must be heat resistant.

This appliance cannot be installed

above fridges, washing machines,

dishwashers or similar.

An oven must have forced ventilation to

install a hob above it.

Check the oven's dimensions in its

installation manual.

If an extractor fan is installed, you must

follow the installation manual's

instructions, always keeping a minimum

vertical distance of 650 mm to the hob.

Preparation of kitchen unit

(fig. 1-2)

Make an appropriate size cut in the work

surface.

If the hob is electric or mixed (gas and

electricity) and there is no oven below,

place a non-flammable separator (e.g.

metal or plywood) 10 mm from the

bottom of the hob. This will prevent

access to the base of the hob.

If the hob is gas, it is recommendable to

place the separator at the same

distance.

On wood work surfaces, varnish the

cutting surfaces with a special glue. This

protects them from moisture.

Installation of appliance

Depending on the model, the adhesive

seal may be factory-fitted. If this is the

case, it should not be removed under

any circumstances, since the adhesive

seal prevents leaks. If the seal has not

been factory-fitted, apply it to the

underside of the hob. Fig. 3.

In order to fit the appliance into the

kitchen unit, tighten each of the clips as

indicated allowing them all turn freely.

Insert and centre the hob.

Press the sides of the hob until it is

supported around its entire perimeter.

Turn the clips and tighten them fully.

The clips position depends on the

thickness of the work surface. Fig. 4

Removal of hob

Turn off the appliance's electricity and

gas supply.

Unscrew the clips and proceed in the

reverse order to installation.

Gas connection (fig. 5)

The end of the inlet connection point of

the gas hob has a 1/2" (20.955 mm)

thread that allows for:

- fixed connection.

- connection using a flexible metal pipe

(L min. 1 m - max. 3 m).

It is necessary to insert the watertight

seal (034308) supplied between the

manifold outlet and the gas supply.

You must prevent the pipe from coming

into contact with moving parts of the

kitchen unit being inserted (for example,

a drawer) and prevent access to any

spaces which might become obstructed.

If you need to connect the gas supply

horizontally, our Technical Assistance

Service can supply you with an L-tube

(code 173018) and a seal (code

034308).

France: substitute the factory-fitted

L-tube for the accessory bag. Fig. 5a.

Please remember to insert the seal.

Warning! If any connection is handled,

check the seal.

Danger of leaks!

The manufacturer is not liable for any

connection leaking, after being handled.

Electric connection (fig. 6)

Check that the voltage and power of the

appliance are compatible with the

electrical installation.

The hobs are supplied with a power

cable with or without a wall socket plug.

Provide an omnipolar cut-off switch with

a minimum contact separation of 3 mm

(except for plug connections, if the user

has access to it).

Appliances with plugs must only be

connected to sockets that have earth

wires correctly installed.

This appliance is type "Y": the supply

cable can only be changed by the

Technical Assistance Service and not

the user. The cable type and minimum

cross-section must be respected.

Changing the gas type

If the country's regulations allow, this

appliance can be adapted to other types

of gas (see specifications plate). The

components required for this are in the

transformation kit supplied (depending

on the model) available from our

Technical Assistance Service. The

following steps should be taken:

A) Change the nozzles (fig. 7-7a):

- Remove the pan supports, burner

covers and diffusers.

- Change the nozzles using the spanner

provided by our Technical Assistance

Service with code 340847 (for double

and triple flame burners code 340808),

see table II, taking special care to

ensure that the nozzle does not fall

when it is removed from the burner or

when fitted.

Ensure that it is completely tightened in

order to guarantee the seal. Primary air

adjustment is not necessary with these

burners.

B) Adjust the taps

Set the control knobs to minimum.

Remove the control knobs from the taps.

Fig. 8. It has an outer seal. Simply press

on this seal with the tip of a screwdriver

to allow access to the tap adjusting

screw. Fig. 8a.

Never remove the seal.

Adjust the minimum ring setting by

turning the by-pass screw using a flat

head screwdriver.

Depending on the gas to which your

appliance is going to be adapted (see

table III), carry out the corresponding

action:

A: firmly tighten the by-pass screws.

B: loosen the by-pass screws until the

gas flow from the burners is correct:

when adjusting the control knob

between maximum and minimum, the

burner does not go out, nor is there a

flame backdraught created.

C: the by-pass screws need to be

changed by an authorised engineer.

D: do not touch the by-pass screws.

If the by-pass screw cannot be

accessed, disassemble the grease

splash tray, which is fixed to the rest of

the hob using a clip and screw mounting

system. The following steps must be

taken to remove the grease splash tray:

- Remove all the burner covers, pan

supports and control knobs.

- Loosen the screws on the burners.

Use the disassembly lever 483196

availablle from our Technical Assistance

Service. To release the front clips, apply

the lever to the area shown in figure 9.

To assemble the grease splash tray

again, proceed in the reverse order to

removal.

It is important that all the seals are

refitted to form a seal.

These devices are essential for the

correct operation of the appliance as

they prevent liquids and dirt from

entering the appliance.

Refit the control knobs.