Siemens EH8 SB3 Series Instrukcja obsługi - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Hob Siemens EH8 SB3 Series. Siemens EH8 SB3 Series 20 stron.

Siemens EH8 SB3 Series Instrukcja obsługi

Time programming function

This function may be used in two different ways:
to automatically switch off a hotplate.
as a timer.

Turning off a hotplate automatically

Enter the cooking time for the required hotplate. The hotplate
turns off automatically once the time has elapsed.
How to program
Select the required power level.
1.
Press the
symbol of the desired hotplate. The hotplate
0
2.
display shows
and the indicator
‹‹
Select the required cooking time in the programming panel.
3.
The possible previous setting is, from left to right 1, 2, 3, etc.,
up to 10 minutes. Within the next 10 seconds, continue
passing through the options in the programming panel until
reaching the desired time.
The cooking time will be displayed for 10 seconds then begin
to count down.
Automatic programming
If the previous setting from 1 to 5 is pressed in the
programming panel, the cooking time is reduced by one
minute, if it is held down the time is automatically reduced to
one minute.
If the previous setting from 6 to 10 is pressed in the
programming panel , the cooking time is increased by one
minute, if it is held down the time is automatically increased to
99 minutes.
Once the time has elapsed
The hotplate switches off. The beep sounds and the display
comes on
‹‹
for 10 seconds. The
Pressing the
symbol turns off the indicators and stops the
0
beeping.
Changing or cancelling the time
Press the
symbol of the desired hotplate. Change the
0
cooking time in the programming panel, or set to

Automatic time limitation

If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. The
heat indicator
/
flash alternatively in the display.
œ
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
comes on.
x
x
indicator lights up.
‹‹
.
symbol and the residual
"‰
Automatically switch off a hotplate with the cooking sensor
function
When cooking using the sensor system, the programmed
cooking time begins to count down once the hotplate reaches
the desired temperature.
Automatically switch off a hotplate with the deep-frying
function
When cooking using the deep-frying function, the programmed
cooking time begins to count down once the selected hotplate
reaches the desired temperature.
Note: Any cooking time can be programmed up to 99 minutes.

Automatic timer

With this function you may select a cooking time for all
hotplates. Once a hotplate is switched on, the selected time will
begin to count down. The hotplate will automatically switch off
when the cooking time has elapsed.
Instructions on activating the timer are found in the chapter
entitled "Basic settings".
Note: The cooking time of a hotplate may be cancelled or
changed:
Press the
symbol of the desired hotplate. Change the
0
cooking time in the programming panel, or set to

Timer

The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. The hob must be switched
on. The timer can be set for any hotplate not turned on. This
function does not automatically switch off a hotplate.
How to program
Press the symbol
for the hotplate, the indicator
0
1.
turned on.
lights up in the time program function display.
‹‹
Select the desired time in the programming panel.
2.
The timer starts to count down after a few seconds.
Once the time has elapsed
A warning beep sounds. In the time program function display
is shown, and the
indicator comes on. After 10 seconds
‹‹
W
the indicators turn off.
Pressing the
symbol turns off the indicators and stops the
0
beep.
Changing or cancelling the time
Press the
symbol of the desired hotplate. Change the
0
cooking time in the programming panel, or set to
Note: When the timer is activated, the corresponding hotplate
is locked. First turn off the timer and then the hotplate.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
.
‹‹
is
W
.
‹‹
15