Ricoh 4510 Instrukcja wymiany - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja wymiany dla Akcesoria do drukarek Ricoh 4510. Ricoh 4510 2 stron. Printer hard disk
Również dla Ricoh 4510: Instrukcja instalacji (4 strony)

Drukuj stronę

Hold the green handle ( ), and slide out the development

Align the new development unit with the rail in the printer.

unit ( ). Put the used development unit in the disposal

Slide the development unit into the printer until it makes a

bag.

click as it locks into place.

ZFCM060J

Important

At the right side of the printer, remove the tape on the left

After removing the development unit, put the unit in the

and right sides of the black sheet, and then pull out the

disposal bag. Be careful not to tilt or shake the unit, otherwise,

sheet using both hands.

toner might scatter.

Important

Take the new development unit from the Type 4510A box.

Do not toucth the green part protected by the black sheet.

Before taking the development unit from the box, be sure to read

the "Removing the Development Unit from the Box" sheet in the

Type 4510A box and follow the instructions.

Important

After taking the new development unit from the box, be careful

not to shake or jar the unit.

Remove the tape with the red tag ( ) and the transparent

tape ( ).

Important

Leave the right cover open, and go to " REPLACING THE FUSING

UNIT".

While pulling out the tape, keep the development unit

horizontal, as shown in the illustration. Tilting or shaking

the unit might cause the toner to scatter.

Do not remove the black sheet until you finish installing the

unit. The black sheet is used to protect the green part of the

development unit.

ZFCM080J

REPLACING THE FUSING UNIT

CAUTION

The fusing unit becomes very hot. When installing the new fusing

unit, turn off the printer and wait for about 30 minutes. After waiting,

install the new fusing unit. Not waiting for the unit to cool down can

result in a burn injury.

Be sure to wait 30 minutes after turning off the printer,

and confirm that it is cool before continuing.

Pull out the standard paper tray (Tray 1), and take the

screwdriver ( ) from the tray.

ZFCM070J

Remove the screw inside the front cover ( ) by turning it

counterclockwise to release the fusing unit.

TAPM090E

ZFCM090E

Important

When removing the screw, press the screwdriver onto the screw

until it makes an audible click as it pops into place.

TAPP761E

Note

You need the screw to lock the new fusing unit afterwards.

Hold the blue knob, and slowly pull the fusing unit out until

Lock the fusing unit in place with the screw you removed

the whole of the green handle is visible.

in step

ZFCM100E

There is the green lever ( ) on the left side of the fusing

Note

unit. While pressing the green lever to the left, slide the

Be sure to return the screwdriver to the paper tray after using

fusing unit out slowly with rasing the green handle and

it.

holding it.

Close the right cover.

ZFCM110E

Take the new fusing unit from the Type 4510B box and

remove the plastic bag.

Important

Do not force the right cover to close. If you cannot close it

easily, confirm that the development unit and the fusing unit

are installed correctly, and that the transfer unit is locked

Remove the two pins with red tag (

), the three

correctly.

transparent tapes ( ) and the desiccant ( ).

ZFCM140J

Note

There is another transparent tape at the bottom of the fusing

unit, make sure to remove the transparent tape.

Place the green handle in the fusing unit. Hold the new

fusing unit with both hands, and keep the unit horizontal.

Align the unit with the rail in the printer ( ), and then

slide the fusing unit into the printer until it stops.

ZFCM120E

Close the duplex unit ( ), and then close the bypass tray

( ).

ZFCM130E

Close the front cover.

Take the gloves off.

ZFCH192E

Turn the printer's power switch on.

Note

The first time you turn the printer on after installation or after

replacing the photoconductor unit, it will make several loud

noises. This is due to the photoconductor unit initializing and

is perfectly normal.

Confirm that the "Change Maint.Kit" message on the

operation panel has cleared.

Replacing the maintenance kit is finished.

Printed in China

UE USA

EE GB