Ricoh Aficio CL5000 Instrukcja szybkiej instalacji - Strona 2
Przeglądaj online lub pobierz pdf Instrukcja szybkiej instalacji dla Akcesoria do drukarek Ricoh Aficio CL5000. Ricoh Aficio CL5000 4 stron. Ricoh cl5000 laser printer quick installation guide
Również dla Ricoh Aficio CL5000: Instrukcje użytkowania (2 strony), Instrukcja szybkiej instalacji (4 strony), Podręcznik uzupełniający (3 strony), Podręcznik (12 strony)
Drukuj stronę
Hold the development unit diagonally to the 45
Confirm the label for the color, and then confirm
degrees as shown in the illustration, and then
that the unit is securely fit in the stoppers.
shake it back and forth 20-25 times.
ZESX414E
Important
When there is a white line showing at the stoppers, reinsert the units.
Hold the unit with the roller facing down.
Important
Do not add shocks to the unit.
If the development unit is not installed properly,
If you do not shake the unit well, it may take longer
the printing quality may be poor.
for the machine to warm up when turned on.
Do not touch the roller or the gears shown in the
Repeat steps
illustration.
development units.
Insert the connectors to the development units
from the bottom ( ) to the top ( ) until they
click into place.
ZESX668E
Set the development unit by aligning the guides,
pushing towards direction (
), and then
inserting slowly until it stops ( ).
Important
Be sure that all four connectors are connected to
the development units. Turning on the power
without all four connectors connected to the units
may cause a printer malfunction.
Close the left cover of the printer by pushing the
fasteners ( ) while holding the cover ( ).
ZESX412E
The illustration shows how to install the black development unit.
The procedure is the same for all four colors.
Note
When installing the development unit, it may come
out a little. This is not a malfunction.
INSTALLING THE FUSER OIL
UNIT
Caution
• Do not incinerate the oil bottle. This could cause
a fire or an injury.
• Spilt oil is very slippery. If oil is spilt, wipe it up
with an alkaline cleaner. Otherwise, the oily
surfaces can create the danger of slipping and
an injury.
• Do not pull out the fusing unit quickly. It may
cause the unit to fall, and result in an injury.
• Do not open the front cover when the paper tray
is pulled out halfway. If you do, it might cause an
injury.
ZESX650J
Open the front cover slowly by pulling down from
the two areas on the left and right.
to
to set the rest of the
Remove the packing material.
Open the Bypass Tray.
ZESX046E
Open the right cover of the printer by pushing up
the handle.
ZESX309E
Remove the packing materials by holding the red
tags as shown in the illustration.
Note
There are two of them.
The fuser oil unit is placed on the fusing unit shown in the
illustration.
ZESX300E
Release the green screw that is fastening the
fusing unit.
ZESX320E
ZESX400E
Note
Use a coin ( ) to release the screw.
The screw cannot be detached.
Holding the handle, pull the fusing unit slowly
until it stops.
ZESX318E
ZESX301E
Take out the new fuser oil unit from the bag.
Remove the covering paper, the seals, and then
the fitting.
Remove the seal
by shaking it to pull.
ZESX319E
ZESX804E
Note
If you cannot remove it easily, pull it out with a
little force.
ZESX910E
Holding the handle, insert the fusing unit slowly
Remove the seal
slowly by turning the fuser oil unit.
until it stops.
ZESX055E
Remove the fitting.
Important
Do not press the fusing unit forcefully into the
printer, as it may cause a printer malfunction.
Fasten the green screw tightly using a coin ( ).
ZESX805E
Note
Be sure to remove the seals to avoid a printer
malfunction.
Be sure to remove the seal
first, and then remove
the seal
to avoid an oil leak.
Be sure to put the fuser oil unit in a stable and level
place to avoid an oil leak.
Close the right cover of the printer.
Oil is on the seals and fusing oil roller after removal.
Be careful not to get it on your hands or clothes.
Holding the green part at the center of the fuser
oil unit, align the shaft of the fuser oil unit with
the metal holder of the fusing unit ( ), and then
set the fusing oil unit firmly by rotating it to the
direction of the arrow ( ).
Note
Press "PUSH" to close the cover firmly.
Close the Bypass Tray.
ZESX054E
Close the front cover slowly by pushing the two
Remove the two red fittings along with the tapes
areas on the left and right.
from the fuser oil unit.
ZESX056E
Go to sheet 2/2.
ZESX325E
ZESX326E
ZESX327E
ZESX328E
Sheet 1/2