Argent BETTE Instrukcja instalacji - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Wanny Argent BETTE. Argent BETTE 6 stron.
Drukuj stronę7 Operating Instructions
Your whirlpool is made from the highest quality steel with a unique glazed finish and it has a
hard smooth surface, it features a German whirlpool system that enhances the hydrotherapy
power of water.
This whirlpool has the following standard features,
1)
Titanium based steel shell ( 30 year warranty)
2)
Safety suction ( prevents getting stuck )
3)
Corrosion resistant galvanised base frame with adjustable feet
4)
Low level water sensor ( pump will not start with out water)
5)
German operating system and pumps ( 1 year warranty)
6)
Rigorous electrical and function testing prior to dispatch
7)
Integral waste/ overflow/ suction system
8)
Combination of Midi and Micro jets, directionally adjustable.
9)
Power matched pump to jet system
10)
Air induced Venturis
This whirlpool may also have the following optional features;
1)
256 Diode LED light
2)
Sanitising system/ Aromatherapy dispenser
3)
15Amp in line heater
Please Note
-
This product is not intended for use by persons with reduced physical, sensory or
mental capacities, or lack of experience or knowledge, unless they have been given supervision
or instruction concerning the use of this whirlpool by a person responsible for their safety.
-
People who have difficulty walking or have another handicap must be extra careful
when getting in and out!
-
Children should be supervised to ensure their safety and that they do not play with
the whirlpool fittings and controls.
-
Please observe the cleaning and care instructions on page 7.
-
Whirlpool pump will not start if the water level sensor is not covered by water.
Fill the bath to 50mm above the highest jet, please remember that once you get in the
whirlpool, water displacement will increase the water level. You may choose to decrease your
initial water level to allow for this displacement; also this will allow you to save water.
Importantly, the system will not start until the low level water sensor is covered.
5
Make sure the power is connected/ turned on at the main supply
Depending on the whirlpool system you have selected, you will have either one or two
control buttons on the rim of your whirlpool.
Main Control Pad, On/Off Button, Light switch
Every Bette whirlpool has this control switch, it has two key pad features, the On/Off pad
and the Light control pad.
On/Off Button
1st Press – Pump starts and runs continuously
2nd Press – This will activate the unique pulsing
feature of the Bette system, where the Pump will
alternately run for 2 seconds, and rest for 2 seconds.
This function will enhance your Whirlpool experience
by giving your body two different stimulations.
3rd Press – this shuts the system down.
Light Switch
This function is only active if you have specified
the 256 diode LED light with your whirlpool.
1st press – Light will cascade thought the myriad
of colour combinations offered by the 256 diode LED light.
2nd Press – Light will remain assigned to red.
3rd Press – Light switches off.
Air Venturi's
Air Venturi's are the additional chrome control(s) located
just below the rim of the Bette Whirlpool. Opening the air
venturis allows for the induction of air into the water via
the jets. This has the simultaneous benefit of both softening
the water and increasing the massaging effect.
Simply turn the air venturi control anti clockwise to open. You may have up to 3 of these,
depending on the amount of jets you have on your whirlpool, see the chart below
10 jet Bette whirlpool
4 midi jets + 6 micro jets
18 jet Bette whirlpool
6 midi jets + 12 micro jets
26 jet Bette whirlpool
26 micro jets
1 air venturi
2 air venturi
6
3 air venturi