Digitalk 2 - WAY COMMUNICATOR Podręcznik użytkownika i instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Podręcznik użytkownika i instrukcja obsługi dla Dwukierunkowe radio Digitalk 2 - WAY COMMUNICATOR. Digitalk 2 - WAY COMMUNICATOR 5 stron.

Drukuj stronę

Operation

Battery Level Indicator:

1. The BATTERY LEVEL is indicated by the number of squares present

inside the BATTERY icon on the LCD Screen.

2. When the BATTERY LEVEL is low, the BATTERY icon will flash to indicate

that the batteries need to be replaced.

3. Do not charge this unit using an AC/DC adaptor with regular "AAA"

alkaline batteries installed. Only use optional AC/DC adaptor with

"AAA" Ni-MH rechargeable batteries (not included).

Battery Charge Indication

During BATTERY CHARGE mode, the BATTERY indicator will keep flashing.

NOTE: Please ensure that the unit is turned off during BATTERY CHARGE

mode.

To Charge The COMMUNICATOR

In the event you wish to use the unit with rechargeable batteries (not

Included) you will be required to use an AC/DC adaptor - Input 230 VAC

50 Hz - Output 6 VDC 100MA (not included).

Remark: Please make sure that the polarity of the plug of the adaptor

is correct. If not, there will be the danger of burning the

COMMUNICATOR. For detailed information of the AC/DC

adaptor, please contact your local dealer.

= Insert 4 "AAA" NI-MH rechargeable batteries (not included)

= Turn the unit OFF

= Plug the adaptor into the wall and insert the round end into the

CHARGE JACK marked CHG on the top of the COMMUNICATOR.

= After charging, unplug the adaptor. Turn the unit ON. The BATTERY

LEVEL INDICATOR on the LCD Screen will display the new BATTERY

LEVEL.

Note: It takes approximately 6 hours to fully charge the batteries if they

are at their lowest level or takes around 14 hours to fully charge

the new batteries.

CAUTION: Do not use non-rechargeable batteries with external AC/DC

adaptor as may cause an explosion, Consult your local dealer.

Operation

To activate the VOX sensitivity:

1. While the VOX mode is on, plug the connector of the headset (not included)

into SPK/MIC jacks of the communicator and then speak through the

microphone of the headset to activate the transmitting mode.

2. Transmitting mode will turn on automatically and on standby mode.

3. The TX LED indicator illuminates red when transmitting.

Note: The VOX sensitivity is automatically activated once plug the connector

of the Headset (not included) into SPK/MIC jacks of the communicator.

You don't have to push the PTT button of the headset while transmitting.

Second Counter Function:

Use for counter second meter from 00 to 99 seconds.

To enter Second Counter mode:

Press MENU

button 5 times to enter Second Counter mode.

While the Second Counter Meter is flashing:

1. Press Up s button to run Second Counter continuously;

2. Press Down t button to pause the Second Counter.

3. Press MENU

button to confirm the second counter and return to

the original default channel automatically;

4. If an active signal is detected while in Second Counter mode, the unit

will return to RECEIVE mode automatically;

To reset the Second Counter meter:

Once enter the Second Counter mode and while it is flashing, press

ENTER

button to reset the Second Counter to 00 status and press

button to confirm.

Duplex Function

This function allows user to use REPEATER feature.

To activate the Duplex function:

Press POWER

button once to enter Duplex or Repeater mode.

Press the button one more time to release the function.

During Duplex mode is on, display will show REP icon.

Operation

Dual Watch:

You can use Dual Watch to monitor 2 channels.

To enter Dual Watch mode:

1. Press MENU

button 3 times.

2. Press Up s and Down t buttons to select desired channel.

3. Once Dual Watch is on, automatically scan the channel that between

2 prefixed channel and the carrier stop on either activated channel

to receive. Dual Watch restarts when the carrier disppears.

4. Press MONITOR M button to monitor weak signal.

, PTT or CALL C button to end the Dual Watch mode.

5. Press ENTER

Internal VOX Control Function

On VOX mode, automatically transmitting and receiving signals without

pressing any button.

To turn on the VOX function:

1. Press MENU

button 4 times to enter the VOX mode;

2. While the VOX icon is flashing;

3. Press Up s button to select higher VOX sensitivity;

4. Press Down t buttons to select lower VOX sensitivity;

5. Press MENU

button twice to confirm the selected mode.

Note: 1. The VOX sensitivity is indicated by the number of bars displayed

in the lower right corner of the LCD Screen.

2. You can press the ENTER

for 4 seconds and adjust the VOX sensitivity to lower level if the

surroundings is too noisy which cause transmitting continuously.

To turn off the VOX function:

1. While the VOX icon is flashing, press Down t buttons until the number

of bars disappears.

2. Press the MENU

button twice to confirm the VOX off mode.

Troubleshooting

SYMPTOM

SOLUTION

No power.

= Check batteries. Ensure that the batteries are installed properly.

= The batteries may be weak.

= Replace old batteries with four (4) new "AAA" alkaline batteries

or Ni-MH rechargeable batteries.

Reception is

= Press the Up s button to increase VOLUME.

weak.

= The receiving signal may be weak and/or out of range.

= If this happens, press the MONITOR M button.

Cannot change

= To change channels, press the MENU

channels.

channel number flashes on the LCD Screen.

= Press the Up s or Down t buttons to change channels.

= Batteries may be weak.

Range is limited.

= BATTERIES may be weak.

= Replace with new batteries if the BATTERY LEVEL indicator is

low.

= The maximum range will vary depending on terrain and

environment.

= Open fields provide the maximum range, while steel/concrete

structures, heavy foliage and use in buildings and in vehicles

may limit the range significantly.

= Wearing the radio close to the body, such as in a pocket or

on a belt, will decrease range; change the location of the

radio.

Sound distortion

= If you are transmitting, speak in a normal tone of voice, 2 to

problems.

3 inches away from the MICROPHONE.

= If you are receiving, lower the volume to a comfortable level.

= Radios too close. Radios must be at least 5 feet apart; increase

your distance.

= Radios too far apart. Obstacles interfere with transmission.

Talk range is up to 2 miles in clear unobstructed conditions.

button twice to stop transmitting

button until the