Cisco TelePresence Video Systems
Contents
Configuring H.323 and SIP
(when not set by a provisioning system)
to get online and ready to place and receive calls, your system
must be set up properly. Your system uses either the H.323
protocol or the SiP protocol for video calls.
NoTe:
Contact your system administrator, or service provider,
for information about the network settings.
for networks administered through Cisco tMS (Cisco
telePresence Management Suite) your Cisco tMS adminis-
trator will help you to get online.
You can find information about administering through Cisco
uCM in the
Administering tC endpoints on CuCM
the diagnostics on your system will indicate if there is a problem
with the H.323 or SiP registering.
If you are changing a value setting,
you have to always click
save
to confirm the change.
Back to task overview
D14639.09 Video Systems Getting Started Guide TC6.1, April 2013.
Introduction
User interfaces
H.323
if in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to the
Configuration
2. open the
3. under
Profile1
the
E164
and the
4. Go to the
if you want the system to obtain the H.323 gatekeeper
address automatically, select
down list; if you want to enter the address manually, select
guide.
Manual.
if set to
Manual
sponding input field.
5. if the H.323 gatekeeper requires authentication and you
want your system to authenticate itself to the gatekeeper,
go to the
the
Mode
Password
otherwise, select
6. Click the
verify the H.323 settings.
if you successfully registered to a Gatekeeper the
is shown as
Please check the Administrator guide for your product if you
wish to change the other H.323 settings.
Confirguration
Configuration
tab and select
System
Configuration.
H323
settings from the left column.
heading and the
H323Alias
subheading, enter
ID
number in their respective input fields.
Gatekeeper
subheading.
Auto
in the
Discovery
enter the gatekeeper
Address
in the corre-
Authentication
subheading and select
drop down list. then enter the
LoginName
in the corresponding input fields.
Off
in the
Mode
drop down list.
Home
tab to see the
System Information
Registered
in the H323 section.
26
Appendices
SIP
if in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to the
Configuration
2. open the
SIP
page from the sidebar on the left.
3. under the
Profle 1
heading, enter the SiP uri in the
input field, and optionally a display name in the
input field.
4. Select the preferred transpor t protocol from the
DefaultTransport
drop down list. if you select Auto, the system
drop
first tries to connect using tls, then tCP, and finally udP.
5. Select a proxy type in the
type is Standard.
6. Go to the
Proxy 1
subheading.
if you want the system to obtain the SiP proxy address
automatically, select
Auto
if you want to enter the address manually, select Manual.
On
in
if you select
Manual
enter the proxy
and
sponding input field.
7. if the SiP proxy requires authentication you must enter a
login name and password to authenticate your system. Go to
and
the
Authentication 1
subheading and enter the
and
Password
in the corresponding input fields.
Status
8. Click the
Home
tab to see the
verify the SiP settings.
if you successfully registered to a SiP server the
shown as
Registered
Please check the Administrator guide for your product if you
wish to change the other SiP settings.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
tab and select
System
Configuration.
URI 1
DisplayName
Type
drop down list. the default
in the
Discovery
drop down list;
Address
in the corre-
LoginName
System Information
and
Status
is
in the SiP section.
Drukuj stronę