Cisco TelePresence Instrukcja instalacji - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla System konferencyjny Cisco TelePresence. Cisco TelePresence 4 stron. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Również dla Cisco TelePresence: Broszura (4 strony), Specyfikacje (7 strony), Podręcznik administratora (27 strony), Skrócona instrukcja obsługi (2 strony), Podręcznik (24 strony), Arkusz instalacyjny (2 strony)

Drukuj stronę
Cisco TelePresence Instrukcja instalacji
Installing Cisco TelePresence System Profile 65"
5
Mounting the wall stand
(applies to wall stand option only)
Long wall bracket
The wall brackets, bracket spacer, and Allen key
are found in the foot module box.
Short wall bracket
WARNING
Due to the size and mass of this equipment,
it is very important that the wall stand is
safely installed according to the installation
instructions, and that the wall is able to safely
support the product.
It is highly recommended that the wall stand is
installed by trained personnel.
1.
Choose the short or long bracket depending
on the required distance between the
bottom module and the wall.
2.
Place the spacer underneath the wall
bracket and fasten the bracket to the bottom
module. Re-use the existing three screws.
Use the Allen key, found in the foot module
box.
3.
Place the bottom module by the wall, mark
where to fasten the bracket and move away
the bottom module.
4.
Add the suitable fixing device for the screws
in the wall.
5.
Connect the the cables (see step 11) and
lead them out at the back before fastening
the unit to the wall.
6.
Place the bottom module by the wall and
fasten it to the wall.
8
Mounting the camera
RJ45
1.
Open the top cover on
RJ45
HDMI
the monitor.
B
2.
Connect the camera
cable to the HDMI and
RJ45 connectors on the
Mounting hole (Tripod) 1/4" UNC
camera.
S/N
Rev
Set the camera DIP switch (country specific setting):
• 50 Hz: 00011, gives 1080p50 (720p50 for HD-SDI).
• 60 Hz: 00100, gives 1080p60 (720p60 for HD-SDI).
3.
Hold the camera
upside down and
carefully slide the
camera into place.
78-19779-02 Profile 65 Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
Choose the short or long bracket
depending on the required distance
between the bottom module and the
wall.
Spacer
Use the spacer between the bottom
module and the wall bracket.
9
Connect camera cables to the codec
1.
Push the camera cable down the channel through the monitor.
2.
Use the two cable clamps to fasten the cable inside the bottom module.
HDMI
3.
Connect the camera cables:
Connect the HDMI cable to the
Connect the 9 pin D-SUb cable
HDMI 1 input at the codec.
to the Camera control input at the
codec.
6
Unpacking the monitor box and mounting the monitor to the base
HEAvY
AND
BULKY
REQUIRES:
4 PEOPLE TO LIfT
CAUTION
NOTE:
Requires 4 people
and lifting straps to lift.
LIFTING STRAPS INCLUDED.
The lifting straps are found
in the box, together with the
monitor, ready for use.
NOTE:
The straps are not
fixed to the monitor. be careful
when lifting the monitor so the
straps do not slide during the
lifting operation.
10
Mounting the grilles in front and finishing up
1.
Close the top cover.
2.
Snap on the top grille.
3.
Snap on the speaker grille.
4.
Remove the plastic foil on the monitor frame.
5.
Use the supplied cloth to clean up the system.
Push the camera cable down the
channel through the Monitor.
Use the cable clamps to fasten the cable
inside the Bottom Module
and connect to the codec.
Camera cable
Camera cable goes
inside the channel.
The codec is placed
inside the front door.
Page 2
7
Connecting the monitor cables
Locate the cables in the bottom module and connect them as described
in the illustration:
1.
HDMI cable
2.
9 pin D-SUb cable
3.
15 pin D-SUb cable
4.
Power cable
A 级声明 (A Class product declaration)
本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
EMC Class A declaration
警告
此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
WARNING:
WARNING:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
11
Connect cables on the rear side
声明所在位置 (Position of the Declaration):
使用说明 User Manual
1.
Locate and connect the cables
铭牌 Nameplate
which are lead out of the system
at the rear side:
• Ethernet cable
申请号 (Application No.)：
• PC cable
申请人 (Applicant):
• Microphone cables
型号
(Model Number)：
• Power cable
2.
Follow the instructions in
the accompanying Touch 8"
installation guide to connect and
initialize the touch interface device.
签字/盖章 Signature/Stamp:
Ethernet cable
日期 Date:
PC cable
Power
cable
Microphone
cables
Connect the microphone cables to the
Microphone connectors on the codec.