Cisco TelePresence Profile 65 Podręcznik dla początkujących - Strona 25
Przeglądaj online lub pobierz pdf Podręcznik dla początkujących dla System konferencyjny Cisco TelePresence Profile 65. Cisco TelePresence Profile 65 46 stron. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Również dla Cisco TelePresence Profile 65: Podręcznik użytkownika (44 strony), Podręcznik dla początkujących (42 strony)
Drukuj stronę
Cisco TelePresence Video Systems
Contents
Configuring IP
(When not set by a provisioning system)
Your video conference system supports IP version 4 (IPv4),
IP version 6 (IPv6) and Dual, which is the default setting. In all
three cases, the IP parameters can be assigned automatically
by the network, or you can set everything manually. When set
to Dual, the network interface can operate on both IP versions,
and have both an IPv4 and an IPv6 address.
If you wish to set the parameters manually, contact your network
administrator to obtain the required parameters.
If you choose to set the IP settings manually while using the
Dual mode, you have to set both the IPv4 and the IPv6 settings.
Start from step 2 in the instructions.
If your system is provisioned automatically, these IP settings
may be overridden by the provisioning system.
If an IPv4 or IPv6 address is already assigned to the system, you
can find it on the System Information page. Go to
tab and choose
System Status
and Network.
NOTE:
It is not recommended to manually change the IP addres
using the web interface.
If you are changing a value setting,
you have to always click
save
to confirm the change.
Back to task overview
D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.
Introduction
User interfaces
To set or change the IPv4 settings
Go to the
Configuration
1.
Choose IP version
Click the
Network
from the
IPStack
2.
If you wish to set IP Assignment manually
In the
IPv4
SubnetMask
Scroll up to the
address in the
3.
Choose automatic or manual IP assignment
Scroll down the page to the
from the
Assignment
IP assignment; or Static, if you have set the IP address
Configuration
manually.
* IP Assignment:
DHCPv6: All IPv6 addresses, including options like the DNS and NTP
server addresses, are obtained automatically from a DHCPv6 server.
Autoconf: The system and gateway IP addresses will be assigned
automatically. The options, e.g. NTP and DNS server addresses, must be
set/assigned according to the DHCP Options setting. **
Static: The system and gateway IP addresses must be configured
manually. The options, e.g. NTP and DNS server addresses, must be set/
assigned according to the DHCP Options setting. **
Configuration
Configuration
tab and choose
System
Configuration.
settings in the left sidebar. Choose
drop down list.
section, enter the Address,
Gateway
in the corresponding input fields.
DNS
section and enter the DNS server
Server 1 Address
input field.
IPv4
section and choose
DHCP
drop down list, if you want automatic
25
Appendices
To set or change the IPv6 settings
Go to the
Configuration
tab and choose
1.
Choose IP version
IPv4
Click the
Network
settings in the left sidebar. Choose
from the
IPStack
drop down list.
2.
Choose automatic or manual IP assignment
and
Scroll down the page to the
DHCPv6,
Autoconf
or
Static
down list according to your network requirements.*
3.
If IP Assignment is Static: Set the IP addresses
Enter the system IP address in the
Optional: Enter the gateway address in the
field.
4.
If IP Assignment is Static or Autoconf: DHCPOptions
Choose
On
or
Off
from the
according to your network requirements.**
If DHCPOptions is Off: Configure DNS and NTP
5.
Scroll up to the
DNS
section, and enter the DNS server
address in the
Server 1 Address
Open the
NetworkServices
and scroll down to the
NTP
address in the
Address
input field. Set
** DHCP Options:
On: The IP parameters, like the DNS and NTP server addresses, will be
obtained automatically from a DHCPv6 server.
Off: The IP parameters, like the DNS and NTP server addresses, must be
set manually.
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
System
Configuration.
IPv6
IPv6
section and choose
from the
Assignment
drop
Address
input field.
Gateway
input
DHCPOptions
drop down list
input field.
settings from the left sidebar,
section. Enter the NTP server
Mode
to Auto.