Sony XCL-U1000C Podręcznik techniczny - Strona 18
Przeglądaj online lub pobierz pdf Podręcznik techniczny dla Kamera Sony XCL-U1000C. Sony XCL-U1000C 27 stron. Digital video camera module
Również dla Sony XCL-U1000C: Instrukcja obsługi (2 strony), Podręcznik (4 strony)
Drukuj stronę
Shutter/Trigger Setting Commands
■ Shutter Speed Setting
[Command]
SHUTTER
[Parameter1] <Shutter setting (0 to 13)>
0: OFF
5: 1/250 s
1: 1/15 s
6: 1/500 s
2: 1/30 s
7: 1/1000 s
3: 1/100 s
8: 1/2000 s
4: 1/120 s
9: 1/5000 s
[Process] Selects a shutter speed.
■ Trigger Mode Setting
[Command]
TRG-MODE
[Parameter1] <Mode (0 to 2)>
0: OFF
t Outputs video in regular mode.
1: Starts exposure to control shutter speed
when an effective external trigger edge is
detected. The selection made in "Shutter
Speed Setting" becomes valid.
2: External pulse width detection
t Controls shutter speed by an external
trigger pulse width. The selection made
in "Shutter Speed Setting" becomes
invalid.
[Process] Sets trigger operation mode.
■ External Trigger Pulse Polarity Setting
[Command]
TRG-POL
[Parameter1] <Mode (0 to 1)>
0: Negative
1: Positive
[Process] Determines the polarity of an external
trigger pulse.
WB Setting Commands (For XCL-U1000C
only)
■ White Balance Mode Setting
[Command]
WBMODE
[Parameter1] <Mode (0 to 4)>
0: 3200K preset
t The preset data for "WB preset
value(3200K)" becomes valid.
1: 5600K preset
t The preset data for "WB preset
value(5600K)" becomes valid.
2: 6500K preset
t The preset data for "WB preset
value(6500K)" becomes valid.
3: WB manual setting
t The value set manually becomes valid.
4: One Push AWB
t Executes "One Push AWB." After
execution, the data becomes valid.
[Process] Selects a white balance mode.
■ Manual R Gain Setting
[Command]
[Parameter1] <Gain (0 to 0xFF)>
10: 1/10000 s
[Process] Sets R gain value in WB manual setting
11: 1/7.5 s
12: 1/2 s
13: 1 s
■ Manual B Gain Setting
[Command]
[Parameter1] <Gain (0 to 0xFF)>
[Process] Sets B gain value in WB manual setting
■ AWB Detection Range Display
[Command]
[Parameter1] <Mode (0 to 1)>
[Process] Selects whether to show or hide the
■ One Push AWB Execution
[Command]
[Process] Performs "One-push AWB" when
Camera Control Command
RGAIN
mode. The parameter is ±128. The
camera regards the R gain value set in
"WB preset value (3200K)" as the
standard value (=0).
BGAIN
mode. The parameter is ±128. The
camera regards the B gain value set in
"WB preset value (3200K)" as the
standard (=0).
AWBWINDOW
0: Display OFF
1: Display ON
detection range display.
AUTOWB
"White Balance Mode Setting: One Push
AWB" is selected. This command is
ignored when White Balance Mode
Setting is not set to "One Push AWB."
The camera does not accept another
command during an execution of
command. The following message
appears when the task is completed.
"AWB OK":
Completed normally.
"LEVEL HIGH":
Failed because the luminance
level is too high.
"LEVEL LOW":
Failed because the luminance
level is too low.
"CTEMP HIGH":
Failed because the color
temperature level is too high.
"CTEMP LOW":
Failed because the color
temperature level is too low.
"TIME OUT":
Time out.
18