Argo XFETTO SCL V2 Instrukcja instalacji - Strona 11
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Klimatyzator Argo XFETTO SCL V2. Argo XFETTO SCL V2 17 stron. Installation instructions for air conditioner
Drukuj stronę
NOTE
Use DRY operation when you want to reduce the humidity
●
in the room.
●
Once the room temperature reaches the set level, the unit
repeats the cycle of turning on and off automatically.
During DRY operation, the fan speed is automatically set
●
(Remote control lamp
Dry operation is not possible if the indoor temperature is
●
10 °C or less.
FAN ONLY
If you want to make air circulate without any temperature
control, press
button until only the
appears on the display.
ADJUSTING THE FAN SPEED
AUTOMATIC
Simply set the FAN selector to the
microcomputer automatically controls the fan speed when
the AUTO mode is selected. When the air conditioner starts
operating, in heating or cooling, the fan speed varies (high
- medium - low - very low) according to the thermal load of
the room.
NOTE
The automatic speed is not available in FAN ONLY mode.
MANUAL
If you want to manually adjust speed just set the FAN selector
as desired.
High speed
Med. speed
NIGHT MODE / ENERGY SAVING
●
This mode enables you to save energy.
1. Set the
or
2. Press the
button.
3. The
mark appears on the display. Press the
button again to release the function.
What does the NIGHT mode mean?
When you select the NIGHT mode, the air conditioner will
modify automatically the set temperature after 60 minutes.
This enables you to save energy without sacrificing your
comfort.
OPERATING MODE
Heating
Cooling and Dehumidifying
NOTA
During the NIGHT mode the internal fan speed is
automatically lower and reduces the noise.
is ON) to prevent overcooling.
fan symbol
position.A
Low speed
selector to cool, dry or heat.
SET TEMPERATURE CHANGE
Lowered by 1 °C
Raised by 2 °C
COOLING AND DEHUMIDIFYING
Function selection
Room temperature
TIME
ELECTRICAL HEATING
This air conditioner is equipped with an electrical heater
that can operate in three ways:
- AUTO MODE - During AUTOMATIC OPERATION the
electrical heater switches on automatically depending on the
room temperature, the set temperature and the outdoor
temperature.
- BOOSTER - During HEATING OPERATION press the
button on the remote control in order to activate the
electrical heater that will switch on only depending on the
room temperature and the set temperature.
- FAN HEATER - During FAN OPERATION press FILTER
button on the remote control or press three times the
selector (blinking symbol
activate the electrical heater.
HIGH POWER MODE
You can select High Power only during cooling or heating
mode and not during automatic, dehumidifying (dry) and
fan mode. High Power mode allows to obtain the maximum
air conditioner's efficiency, either in cooling or heating mode
(heat pump). The user can choose to activate the High
Power mode, using the remote control unit, after having
selected cooling or heating mode and during this latter
mode, it can be used together with the electrical heater in
Booster way. Under these conditions the air conditioner
will reach its maximum thermal power and consequently
also the maximum electrical consumption and noise; it is
recommended to use the High Power mode only if the
outdoor temperature is very low and the selected room
temperature is difficult to be reached. On the contrary, if
you want to obtain the best performance in efficiency and
silentness, High Power mode is not recommended: let the
air conditioner run in normal condition (factory default
program).
To activate High Power mode it is necessary (after having
selected the cooling or heating mode) to press two times
the HIGH POWER button
acoustic signal confirmation); at the first pressure of the
button the symbol .....switches on, at the second pressure
this symbol disappears; at this point the operation lamp
(green lamp on the front panel of the air conditioner) begins
blinking slowly, indicating that High Power mode is activated;
it can be deactivated using the same procedure; therefore
the green lamp will stop blinking and it will be switched on
permanently.
10
HEATING
Function selection
Room temperature
TIME
on the display) in order to
(always waiting for the
EG