Sony XCL-S600C Broszura - Strona 3

Przeglądaj online lub pobierz pdf Broszura dla Aparat cyfrowy Sony XCL-S600C. Sony XCL-S600C 4 stron. Xcl-s series digital video camera module

Drukuj stronę
Sony XCL-S600C Broszura
Sensitivity Control
The XCL-S Series is equipped with a saturation signal control
function to allow the amount of saturation signal charge
on the CCD to be increased or decreased via software
commands. For example when capturing dark objects, the
user can increase the amount of saturation signal charge –
this elevates the camera's sensitivity to improve the picture
quality instead of using a long exposure time.* On the other
hand, by decreasing the amount of saturation signal charge,
the level of smear can be reduced or improved.
* If the saturation signal charge amount exceeds the maximum that can
be transferred into the vertical and horizontal registers, a transfer error will
occur (e.g., smear).
User Set
In addition to factory default settings, up to 16 camera
parameters – including brightness, gamma, shutter, gain, and
trigger mode – can be preset to suit each particular scene.
CH 1
CH 2
Bulk Trigger Mode & Sequential Trigger Mode
These new XCL-S Series cameras feature advanced
Bulk Trigger and Sequential Trigger modes in addition to a
conventional trigger mode. Each camera can store up to 16
different camera setups (e.g., exposure, and gain).
Bulk Trigger mode allows these cameras to capture up to
16 images in rapid succession using a single software or
hardware trigger.

PIN ASSIGNMENTS

DC IN
DC IN (DC power input) connector (12-pin)
Pin No.
Signal
Pin No.
1
Ground
5
2
DC +12 V
6
3
ISO Ground
7
4
GPI1 / GPO1
8
DIGITAL IF (Interface) connector (26-pin)
Pin No.
Signal
Pin.No.
1
Ground
10
2
X0–
11
3
X1–
12
4
X2–
13
5
XCLK–
14
X3–
6
15
7
Ser TC+
16
8
Ser TFG–
17
9
CC1–
18
CH 3
CH 16
DIGITAL IF
Signal
Pin No.
Signal
GPO2 (ISO-)
9
GPO4 (ISO)
GPO2 (ISO+)
10
GPI4 (ISO+)
GPI3 / GPO3
11
GPI2
GPI4 (ISO-)
12
ISO Ground
Signal
Pin.No.
Signal
CC2+
19
X3+
CC3–
20
Ser TC–
CC4+
21
Ser TFG+
Ground
22
CC1+
Ground
23
CC2–
X0+
CC3+
24
X1+
25
CC4–
X2+
26
Ground
XCLK+
Sequential Trigger mode allows each camera to capture a
single image using successive setups stored in the user set
with each software or hardware trigger.
1
2
3
CH 1
CH 2
CH 3
Sequential Trigger mode
Look-up Table (LUT)
Each XCL-S Series camera supports a look-up table which
transforms the input luminance signal into the required
digital output. It supports factory presets – Linear, Negative,
Binarization, and Linear Interpolation – as well as a User-
defined LUT (input: 12 bits, output: 12 bits).
Trigger Noise Filtering
With a trigger line filter, these cameras can specify a valid
pulse width for the trigger. This helps avoid unexpected
image capture caused, for example, by triggers from
insignificant noise.
Pulse Train Generator
XCL-S Series cameras are capable of outputting any
rectangular wave from one of the general-purpose outputs.
This pulse train can be programmed for frequencies from
0.5 Hz up to 100 KHz in 1 µs steps to control external devices
such as LED lights, simplifying overall system configuration.
DIMENSIONS
10.5 (
/
)
7
16
50 (2)
40 (1
/
)
5
8
8
(1
/
)
1
32
4-M3 Depth 4 (
/
)
3
16
10.5 (
/
)
7
16
1
CH 1
CH 2
CH 3
Bulk Trigger mode
2-M3 Depth 4 (
/
)
3
16
65.5 (2
/
)
5
8
57.5 (2
/
)
3
8
50 (2)
4-M3 Depth 4 (
/
)
3
16
Unit: mm (inches)