Sony WX-920BT Instrukcja obsługi - Strona 20

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System stereo Sony WX-920BT. Sony WX-920BT 38 stron. Bluetooth audio system

Drukuj stronę

E:\4699684111\4699684111WX920BTUC\01GB-WX-920BTUC\030CD.fm

010COV.book Page 20 Wednesday, June 7, 2017 7:11 PM

PARENTAL (parental)

Sets the parental lock to [ON], [OFF], and edits

the passcode (page 12).

(Available only when SiriusXM is selected.)

SXM SIGNAL (SiriusXM signal)

Displays the current status of the SiriusXM signal

strength: [NO SIGNAL] (signal level 0), [WEAK]

(signal level 1), [GOOD] (signal level 2),

[EXCELLENT] (signal level 3)

(Available only when SiriusXM is selected.)

SXM RESET (SiriusXM reset)

Initializes the SiriusXM Connect Vehicle Tuner

settings (preset channels/parental lock): [YES],

[NO].

(Available only when SiriusXM is selected.)

FIRMWARE (firmware)

(Available only while the source is off and the

clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES], [NO].

Updating the firmware takes a few minutes to

complete. During the update, do not turn the

ignition to the OFF position, nor remove the USB

device.

Sound Setup (SOUND)

This setup menu is not available when the source is

off and the clock is displayed.

EQ10 PRESET (EQ10 preset)

Selects an equalizer curve from 10 equalizer

curves or off:

[OFF], [R&B], [ROCK], [POP], [HIP-HOP], [EDM],

[JAZZ], [SOUL], [COUNTRY], [KARAOKE]*,

[CUSTOM].

The equalizer curve setting can be memorized

for each source.

* [KARAOKE] reduces the vocal sound but

cannot fully remove it during playback. Also,

using a microphone is not supported.

EQ10 CUSTOM (EQ10 custom)

Sets [CUSTOM] of EQ10.

Setting the equalizer curve: [B1] 32 Hz, [B2]

63 Hz, [B3] 125 Hz, [B4] 250 Hz, [B5] 500 Hz, [B6]

1 kHz, [B7] 2 kHz, [B8] 4 kHz, [B9] 8 kHz, [B10]

16 kHz.

The volume level is adjustable in 1 dB steps,

from -6 dB to +6 dB.

BALANCE (balance)

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER (fader)

Adjusts the relative level: [FRONT-15] – [CENTER]

– [REAR-15].

SUBWOOFER (subwoofer)

SUBW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+6 dB] – [0 dB] – [-6 dB].

([ATT] is displayed at the lowest setting.)

SUBW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORMAL],

[REVERSE].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency: [80Hz],

[100Hz], [120Hz].

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off frequency:

[OFF], [80Hz], [100Hz], [120Hz].

AUX VOLUME (AUX volume)

Adjusts the volume level for each connected

auxiliary device: [+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust the

volume level between sources.

(Available only when the AUX is selected.)

masterpage: Left

WX-920BT

4-699-684-11(1)