Digiview RC61ELW Podręcznik użytkownika - Strona 3
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Budzik Digiview RC61ELW. Digiview RC61ELW 8 stron. Travel alarm clock with atomic time and temperature
Drukuj stronę
MANUAL SETTINGS
TIME ZONE
PM
* Select the Time Zone by pressing and
holding the UP (+) button for 3 seconds.
MONTH
* Keep holding UP (+) button until the
desired time zone (Pacific, Mountain,
Central or Eastern) is highlighted on
PM
the clock's display map.
MONTH
CLOCK
PM
* Press and hold MODE button for 3
seconds: the year digit will flash.
MONTH
* Press UP (+) or DOWN (-) to
change flashing digits.
PM
* After the first value is set, press
MODE button again to confirm and
MONTH
move to the next parameter.
* Continue setting month, date, hour
and minutes and the temperature
PM
display in Celsius or Fahrenheit.
* Press MODE button for the last
MONTH
time to confirm the settings after
the last parameter is set.
PM
MONTH
PM
MONTH
PM
MONTH
8
SETTING THE ALARM
To set the Alarm1,
* Press MODE button once to display
PM
ALARM TIME 1. If the alarm is off,
the default time "6:00" will be
MONTH
displayed.
* Press and hold 1SET button for two
PM
seconds. The hour digit will flash.
* Enter the hour using DOWN (-) or
MONTH
UP (+).
* Press 1SET button again. The minute
digits will flash.
PM
* Enter the minutes using DOWN (-)
or UP (+).
MONTH
* Press 1SET button again to confirm:
an icon [
] will appear on the
1
display next to the alarm time.
PM
* Repeat the same procedure to set an
Alarm2, using 2SET button.
MONTH
LIGHT/SNOOZE
When the alarm sounds, press the LIGHT/SNOOZE button
to temporarily stop the alarm. After the LIGHT/SNOOZE
is depressed, the alarm sound will resume in five minutes.
If the alarm is not disabled after that, it will sound for
four more minutes and then will stop by itself.
DISABLING ALARM
Press 1SET or 2SET buttons on the unit to disable any of
the alarms.
When Al1 and Al2 are disabled, an applicable icon [
or [
] disappears from the unit's display.
2
10
TIME FORMAT
* Press UP(+) button to toggle
between 12 and 24 hour time format
DATE
DATE
DAY OF THE WEEK LANGUAGE
* Press and hold DOWN (-) button
for 3 seconds: the default language
abbreviation will flash ( example – EN)
DATE
* Continue holding DOWN (-) button
until the desired day of the week
language abbreviation is selected.
* Release the DOWN (-) button to
confirm the setting.
DATE
DATE
ALARMS
There are two available alarms –Alarm 1 and Alarm 2.
DATE
If any of alarms is activated, it will sound at the set time
and the alarm icon will flash Mondays through Fridays.
DATE
DATE
PROGRAMMING THE SNOOZE INTERVAL
* Press and hold 1SET button for two seconds to activate an
Alarm1 programming mode. Alarm1 hour digit will flash.
* Adjust the desired hour using UP (+) or DOWN (-)
buttons.
DATE
ALARM1
* Press 1SET button: the minute digits will flash.
* Adjust the desired minutes using UP (+) or
DOWN (-) buttons.
* Press 1SET button again: the snooze interval minutes
DATE
ALARM1
will flash.
* Adjust the desired interval time
using UP (+) or DOWN (-) buttons.
DATE
ALARM1
* Press 1SET button to confirm set snooze interval.
Use the same procedure to program the snooze interval for
Alarm2.
DATE
ALARM1
INDOOR TEMPERATURE
1
The indoor temperature shares the same display's line
with the calendar and the day of the week.
NOTE: If the indoor temperature goes above or below
operating range stated in specifications, the display will
show dashes [
]
PRECAUTIONS
This product is engineered to give you years of satisfactory
service if handled carefully. Here are a few precautions:
* Do not immerse the unit in water.
* Do not clean the unit with abrasive or corrosive
materials. They may scratch the plastic parts and
]
1
corrode the electronic circuits.
* Do not subject the product to excessive force, shock,
dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries, and
damaged parts.
AM
MONTH
DATE
MONTH
DATE
PM
MONTH
DATE
PM
MONTH
DATE
PM
MONTH
DATE
9
PM
MONTH
DATE
ALARM1
11