Epson C11C422001 - FX 880+ B/W Dot-matrix Printer Informacje o produkcie - Strona 16

Przeglądaj online lub pobierz pdf Informacje o produkcie dla Akcesoria do drukarek Epson C11C422001 - FX 880+ B/W Dot-matrix Printer. Epson C11C422001 - FX 880+ B/W Dot-matrix Printer 17 stron. Warranty statement
Również dla Epson C11C422001 - FX 880+ B/W Dot-matrix Printer: Instrukcja instalacji (10 strony), Specyfikacja (2 strony), Instrukcja montażu (8 strony), Ograniczona gwarancja (1 strony)

Drukuj stronę

Epson C11C422001 - FX 880+ B/W Dot-matrix Printer Informacje o produkcie

EPSON FX-880/FX-1180

2. To enter hex dump mode, hold down both the

buttons while you press the

Load/Eject

turn on the printer.

3. Open a software program and send a print job to the

printer. Your printer prints all the codes it receives in

hexadecimal format.

If characters are printable, they appear in the right column

as ASCII characters. Nonprintable codes, such as control

codes, are represented by dots. By comparing the characters

printed in the right column with the printout of the

hexadecimal codes, you can check the codes the printer is

receiving.

4. To turn off hex dump mode, press the

the printed page(s), and then turn off the printer.

Cleaning the Printer

To keep your printer operating at its best, you should clean it

thoroughly several times a year. Follow these steps:

1. Remove any paper loaded in the printer, and turn off the

printer. Then remove the paper guide. If an optional cut-

sheet feeder is installed, remove it.

2. Use a soft brush to carefully brush away all dust and dirt

from the outer case and paper guide.

3. If the outer case or paper guide is still dirty, clean it with a

soft, clean cloth dampened with mild detergent dissolved in

water. Keep the printer cover and front cover closed to

prevent water from getting inside the printer.

Caution:

Never use alcohols or thinners to clean the printer;

these chemicals can damage the printer components

as well as the case.

Be careful not to get water on the printer mechanism

or electronic components.

Do not use a hard or abrasive brush.

Do not spray the inside of the printer with lubricants;

unsuitable lubricants can damage the printer

mechanism. Contact an EPSON dealer if you think

lubrication is needed.

16 - EPSON FX-880/FX-1180

and

LF/FF

button to

Operate

button, eject

Pause

11/98

Transporting the Printer

If you need to transport your printer some distance, carefully

repack it using the original box and packing materials, as

described below.

1. Remove any paper loaded in the printer, and turn off the

printer. Then remove the paper guide.

2. Unplug the power cord from the electrical outlet; then

disconnect the interface cable from the printer.

3. If an optional cut-sheet feeder is installed, remove it. If any

other options are installed, remove them and pack them in

their original boxes.

Warning:

If you just used the printer, the print head may be hot;

let it cool before you remove the ribbon cartridge.

4. Remove the ribbon cartridge as described on page 12.

5. Make sure the paper tension unit is installed and the tractor

is installed in the rear push position. Close the printer cover

and front cover.

6. Repack the printer, ribbon cartridge, paper guide, and

power cord (if necessary) in the original packing materials

and place them in the printer's original box.

Epson C11C422001 - FX 880+ B/W Dot-matrix Printer Informacje o produkcie - Strona 16

Cleaning the Printer

Transporting the Printer

Related Documentation