Acuity Brands Lighting 6BPMW LED Instrukcje instalacji

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Jednostka sterująca Acuity Brands Lighting 6BPMW LED. Acuity Brands Lighting 6BPMW LED 5 stron. 6"/5"/4" baffle led module

Drukuj stronę

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE

INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from ﬁ re, electric

shock, falling parts, cuts/abrasions, and other hazards please read all warnings and

instructions included with and on the ﬁ xture box and all ﬁ xture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment,

follow these general precautions.

• Installation and service of luminaires should be performed by a qualiﬁ ed licensed

electrician.

• Maintenance of the luminaires should be performed by person(s) familiar with the

luminaires' construction and operation and any hazards involved. Regular ﬁ xture

maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency

of cleaning will depend on ambient dirt level and minimum light output which is

acceptable to user. Refractor/lens should be washed in a solution of warm water and

any mild, non-abrasive household detergent, rinsed with clean water and wiped dry.

Should optical assembly become dirty on the inside, wipe refractor/lens and clean in

above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly

packed so that no parts should have been damaged during transit. Inspect to conﬁ rm.

Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please

visit

www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment nor to

provide every possible contingency to meet in connection with installation, operation,

or maintenance. Should further information be desired or should particular problems

arise which are not covered sufﬁ ciently for the purchaser's or owner's purposes, this

matter should be referred to Acuity Brands Lighting, Inc.

WARNING RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.

• Verify that supply voltage is correct by comparing it with the luminaire

label information.

• Make all electrical and grounded connections in accordance with the National

Electrical Code (NEC) and any applicable local code requirements.

• All wiring connections should be capped with UL approved recognized

wire connectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton,

installing, servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

• Allow lamp/ﬁ xture to cool before handling. Do not touch enclosure or light source.

• Do not exceed maximum wattage marked on luminaire label.

• Follow all manufacturer's warnings, recommendations and restrictions for: driver

type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.

• Do not operate in close proximity to persons, combustible materials or substances

affected by heat or drying.

LED IMPORTANT SAFETY INSTRUCTIONS

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.

• Do not mount or support these ﬁ xtures in a manner that can cut the outer jacket or

damage wire insulation.

• Never connect an LED product to an unapproved dimmer pack. Contact ABL

directly for any dimmers not speciﬁ cally recommended for the product.

• Unless individual product speciﬁ cations deem otherwise: Allow for some volume of

airspace around ﬁ xture. Avoid covering LED ﬁ xtures with insulation, foam, or other

material that will prevent convection or conduction cooling.

• Unless individual product speciﬁ cations deem otherwise: Maximum ambient

temperature is 90°C. Do not operate ﬁ xture at temperatures higher than this.

• Unless individual product speciﬁ cations deem otherwise: Never mount in places

where ﬁ xture will be exposed to rain, high humidity, extreme temperature changes

or restricted ventilation.

• LED products are Polarity Sensitive. Ensure proper Polarity before installation.

• Electrostatic Discharge (ESD): ESD can damage LED ﬁ xtures. Personal grounding

equipment must be worn during all installation or servicing of the unit.

• Do not touch individual electrical components as this can cause ESD, shorten lamp

life, or alter performance.

• There are no user serviceable parts inside the unit. Do not rewire, reconﬁ gure,

or modify the unit or attempt any repairs yourself. Additionally, ﬁ eld replacement

of the LED assembly or lamps is not allowed by UL standards at this time. In the

unlikely event your unit may require service, stop using the unit immediately and

contact an ABL representative.

All luminaires that contain electronic devices that generate frequencies above 9kHz from

any component within the luminaire comply with one of the following Part 15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference

that may cause undesired operation.

This device complies with Part 18 of the FCC Rules but may cause interference with

cordless and cell phones, radios, televisions, and other electronic devices. To correct

the problem move the device away from the luminaire or plug into a different outlet.

This product may cause interference to radio equipment and should not be installed near

maritime safety communications equipment or other critical navigation or communica-

tions equipment operating between 0.45-30MHz.

Failure to follow any of these instructions could void product warranties.

For a complete listing of product Terms and Conditions, please visit

www.acuitybrands.com.

OUR BRANDS

Indoor/Outdoor: Lithonia Lighting, Carandini, Holophane, RELOC

Indoor Lighting: Gotham, Mark Architectural Lighting, Peerless, Renaissance

Lighting, Winona Lighting

Outdoor Lighting: American Electric Lighting, Antique Street Lamps, Hydrel, Tersen

Controls: DARK TO LIGHT, Lighting Control & Design, ROAM, Sensor Switch,

Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of

improper or careless installation or handling of its products.

ABL LED General Warnings, Form No. 503.203