Crowcon APM 155 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przyrządy pomiarowe Crowcon APM 155. Crowcon APM 155 2 stron. Pressure meter

Drukuj stronę

Test Menu – Pressure Test

Used for timed pressure tests.

Durations, pass & fail controlled by user

Test can be set to monitor lapsed time or the user can

set a countdown timer which alerts user when the

timer expires.

2-stage exit of test so that an accidental press of the

Escape button prevents the automatic termination of

the test.

Data can be stored & shared.

Test Menu – Strength Test

Used for timed strength tests.

Durations, pass & fail controlled by user

Test can be set to monitor lapsed time or the user can

set a countdown timer which alerts user when the

timer expires.

2-stage exit of test so that an accidental press of the

Escape button prevents the automatic termination of

the test.

Data can be stored & shared.

Units of Measurement

Select this menu option to change the pressure units

displayed on the meter.

Settings Menu – Auto off timeout

Changes the period when the unit will switch off if

inactive.

Settings Menu – Backlight

Changes the brightness of the backlight.

Lower settings will prolong battery life.

Settings Menu – Key Click

Enable/disable button click.

Settings Menu – Report

Change report sending option (printer, wireless or

toggle).

Settings Menu – Supervisor Settings

User configurable settings. Allows setting of time and

date, owner/company name and user password.

Stored Logs Menu

Search and retrieve stored logs. Allows log to be

reviewed, re-printed or re-transmitted over the

wireless link.

BATTERY REPLACEMENT

1. Remove the protective rubber boot by slipping it

away from the bottom of the case and sliding it over

the pressure spigots exposing the case back.

2. Remove the battery cover from the bottom of the

case by removing the four screws.

3. Remove the three AA batteries and replace with

good quality AA Alkaline batteries taking care to

install them the right way round.

4. Replace the battery cover carefully making sure it is

alligned properly and replace the screws. Take care

not to over tighten the screws otherwise it may

damage the case.

For best results and longer life always use quality

alkaline batteries MN1500 or equivalent.

CAUTIONS

Exposure to silicone based products, corrosive gases,

water / condensation and freezing should be avoided

at all times as this will cause damage to the sensor

and internal component corrosion.

This instrument should not be stored or operated

outside of its operating temperature range.

Particular care must be taken not to exceed the

maximum pressure ratings for the device as this

may rupture the sensor membrane. This is not

covered by the manufacturer's warranty.

NOTE: The differential/gauge instruments will only

measure positive pressures i.e. positive pressure

applied to positive port, or negative pressure applied

to the negative port.

WARRANTY

This instrument is guaranteed against defects of

workmanship and materials for a period of twelve

months from date of invoice.

During the warranty period a defective instrument will

be repaired or replaced at the discretion of the

manufacturer. This warranty does not cover damage

or failure due to misuse or accident. Modification,

adjustment or any alteration shall void the warranty.

For any warranty claims to be considered the

instrument must be returned to Anton along with proof

of purchase at the senders cost.

FCC Compliance

NOTE: This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated

in a commercial environment. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance

with the instruction manual, may cause harmful

interference to radio communications. Operation of

this equipment in a residential area is likely to cause

harmful interference in which case the user will be

required to correct the interference at his own

expense.

SPECIFICATIONS

Power Supply

3 x AA Alkaline Batteries

Battery Life

> 20 hours*

Duty Cycle

Continuous.

Auto switch off after 5 mins.

Operating

-10 to +50 °C

Temperature

Weight

395 grams including

batteries

Dimensions

185 x 75 x 43 mm

Accuracy

±2% of reading

* Using recommended Industrial batteries

Units

APM 155

mbar

0.0 to +2000.0

PSI

0.000 to +29.000

mmHg

0.0 to +1500.0

mmH

0 to +20394

0.000 to +20.394

inHg

0.00 to +59.06

inH

0.00 to +802.9

kPa

0.00 to 200.00