Epson Stylus Photo 820 Zacznij tutaj

Przeglądaj online lub pobierz pdf Zacznij tutaj dla Akcesoria do drukarek Epson Stylus Photo 820. Epson Stylus Photo 820 2 stron. Product support bulletin(s)
Również dla Epson Stylus Photo 820: Instrukcje instalacji (5 strony), Arkusz specyfikacji (1 strony), Uwaga dotycząca programowania (18 strony), Biuletyn wsparcia produktu (6 strony), Biuletyn wsparcia produktu (1 strony), Podręcznik uzupełniający (1 strony), Podręcznik użytkownika (27 strony), Podręcznik zgodności (1 strony), Karta informacyjna produktu (4 strony), Specyfikacje (2 strony), Informacje o produkcie (11 strony), Specyfikacje (2 strony), Biuletyn wsparcia produktu (3 strony), Biuletyn wsparcia produktu (2 strony), Biuletyn wsparcia produktu (4 strony), Biuletyn wsparcia produktu (7 strony)

Drukuj stronę
Epson Stylus Photo 820 Zacznij tutaj
EPSON Stylus

Start Here

Start Here
1
1
Unpack
1
Remove everything from the box.
printer
paper support
2
Remove all the tape and
packing material.
3
Peel off the tape beneath the cover
and remove the insert.
4
Insert the paper support
into its three slots.
2
2

Connect the Printer

Connect the printer to your computer using either a USB cable or parallel cable. Don't connect both
cables; you only need one or the other. Follow the instructions in the appropriate section below.
If You Have a USB Port
(Does not support Windows
95 or Windows NT
®
1
Make sure the printer and computer are turned off.
2
Connect the
square end of the USB cable to your printer's USB port.
3
Connect the
flat end of the cable to any available USB port on your computer.
If You Have a PC Parallel Port
1
Make sure the printer and computer are turned off.
2
Connect the larger end of the parallel cable to your printer's parallel port.
Then secure it with the wire clips.
3
Connect the other end of the cable to your computer's parallel port and secure it as necessary.
®
Photo 820
ink cartridges
CD-ROM
Printer Basics
remove the
insert
.)
®
3
3
Power On
1
Plug the printer into a grounded electrical outlet.
2
Press the
power button to turn on the printer.
Don't turn on your computer yet.
Don't use an outlet controlled by
a wall switch or timer. Never use a
power strip switch to turn the
printer on or off; use only the
printer's
power button.
4
4

Load Ink

1
Open the output tray and
raise the printer cover.
2
Lift up the ink cartridge clamps.
You must install both
cartridges or the printer
won't work.
3
Unpack the ink cartridges that came with
your printer and remove the yellow tape.
Keep cartridges out of the reach
of children.
4
Tilt each cartridge toward you as you lower it. Make sure the tabs rest on the hooks.
black
hooks
5
Lower the clamps so they snap shut.
6
Press the
ink cartridge replacement button
and close the printer cover. You see the green
power light flash and you hear the printer
make noise. Wait until ink charging is finished
(the green
power light stops flashing).
Don't turn off the printer or interrupt ink charging
while the
power light is flashing or you'll use up
more ink than necessary when you turn it back on.
5
5

Load Paper

1
Load some paper behind the tabs
inside the edge guides.
2
Press in the locking tab on the
left edge guide and slide it snugly
against the edge of the paper stack.
3
Pull out the output tray extension.
2
1
Don't place the cartridge tabs
color
under the hooks, or you may
damage the clamp when you
close it.
ink cartridge
replacement
button
2
Turn over
power button
1
3