Dimas MX 140 E Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Elektronarzędzie Dimas MX 140 E. Dimas MX 140 E 20 stron. Mixer

Drukuj stronę

Electrical connection

- ELECTRICAL SAFETY :

Operate this machine only on a

supply equipped with a 30 mA

earthed current-limiting circuit-

breaker. Otherwise, consult our

catalogue for appropriate models.

- The RCCB must be used

correctly, including testing it

regularly. For tools supplied

with an integral RCCB in the

cable or in the mains plug, if

the cable or plug has been

damaged, repairs must be

carried

out

manufacturer, one of his

agents or by a qualified repair

workshop to avoid any risks

resulting from errors.

• Motor power supply : reinforced electric

cable

with

(3xPx+xE)

(3xPx+xNx+xE) conductors 2.5 mm

lengths less than 100 m.

• Earthing of the machine (mandatory).

Fitting the tool

Motor off

Disconnect by removing the plug.

• Mixers have an M14 internal thread.

Keep the thread and the external

surfaces clean.

• If the mixer becomes loose, tighten with a

22 mm open ended spanner

• Clean your tools thoroughly to work better

and more safely.

Starting

Always take care.

Get into a comfortable, balanced

position.

Remove all adjustment tools and

wrenches

from

floor

machine

The machine has an electronic speed

control which prevents material flying when

the machine is turned on.

The speed may be controlled by varying the

pressure exerted on the controls.

• Momentary action switch :

¤ On : press the switch

¤ Off : release the switch

• Latching switch :

¤ On : press the switch and latch it using

the button

¤ Off : press the switch again and

release it

• During operation, always hold the

machine in both hands and work in a

stable position.

• Protect yourself against electrical

discharge. Do not touch equipment that is

earthed such as conduits, radiators . . .

the

• Always keep the machine cable behind

you.

for

Important advice

• Retighten the bolts regularly, in particular

after the first hours of use.

The manufacturer declines all

responsibility for loss or damage

resulting from misuse or any

modification,

powering that does not conform

to the manufacturer's original

specifications.

At the work station, the sound

pressure level may exceed 85 db

(A)

In this case individual protection

measures must be taken.

Servicing and maintenance

The machine is designed to require only

minimum servicing and maintenance.

Make sure that the following points are

observed :

• Keep the machine clean.

• Do not allow any foreign body to

penetrate into the electrics.

• After about every 300 hours of use have

the brushes inspected by a specialist. If

they are less than 5 mm long, replace

with new brushes. The brushes should be

operated off load for about 20 minutes.

• At the same time, also check the

condition of the commutator. If the blades

are not uniform in colour and there are

and

surface stripes, the machine should be

sent to an approved workshop.

• The gear box and drive shaft should be

cleaned after 500 hours of operation.

• At this stage, the whole machine requires

servicing and should be sent to an

approved workshop.

Repairs

Contact your supplier who is

entirely at your service to carry

out repairs in the shortest time at

the best possible price.

Spare parts

For rapid delivery of spares and in order to

avoid any wasted time, it is necessary to

remind your supplier of the details shown

on the instruction plate on the machine with

each order, as well as the reference of the

part to be replaced.

alteration

Scrapping

In the event of deterioration and

scrapping of the machine, the

following

disposed of in accordance with

the

legislation in force.

• Main materials :

¤ Motor : Aluminium (AL) - Steel (AC),

Motor :

Copper (CU) - Polyamide (PA)

¤ Machine : Steel sheet (AC) -

¤ Machine :

The instructions for use and spare

parts found in this document are for

information only and are not binding.

As part of our product quality

improvement policy, we reserve the

right to make any and all technical

modifications without prior notice.

items

must

requirements

the

Cast iron (FT) -

Aluminium (AL)