Toshiba 38TVDA010 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Klimatyzator Toshiba 38TVDA010. Toshiba 38TVDA010 12 stron.

Drukuj stronę

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

● Pressing the RESET button, the unit can start

or stop without using the remote control.

● Operation mode is set on AUTOMATIC

operation, preset temperature is 24°C and fan

operation is automatic speed.

AUTO RESTART FUNCTION SETTING

This product is designed so that, after a power failure, it can restart

automaticallyin the same operating mode as before the power failure.

Information

The product is shipped with Auto Restart function in the ON position.

Turn it OFF if this function is not required.

How to turn OFF the Auto Restart Function

• Press and hold the [OPERATION] button on the indoor unit for 3 seconds

(3 beep sounds but OPERATION lamp does not blink).

How to turn ON the Auto Restart Function

• Press and hold the [OPERATION] button on the indoor unit for 3 seconds

(3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).

Note:

• In case of ON timer or OFF timer are set, AUTO RESTART OPERATION

does not activate.

SELF CLEANING OPERATION

(COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during "Cool" or "Dry" mode,

the fan will continue to run for other 30 minutes, then it will turn off

automatically. This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the

within 30 seconds.

MAINTENANCE

Firstly, turn off the circuit breaker.

Indoor Unit and Remote Control

● Clean the indoor unit and the remote control with a wet cloth when

needed.

● No benzine, thinner, polishing powder or chemically-treated duster.

Air filters

Clean every 2 weeks.

1. Open the air inlet grille.

2. Remove the air filters.

3. Vacuum or wash and then dry them.

4. Reinstall the air filters and close the air inlet grille.

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being

activated for 3 minutes when suddenly restarted or switched to ON.

2. Some minor cracking sound may occur when unit operating. This is

normal because the cracking sound may be caused by expansion/

contraction of plastic.

Air conditioner operating conditions

Temp.

Outdoor Temperature

Operation

Cooling

-10°C ~ 46°C

Dry

-10°C ~ 46°C

TROUBLESHOOTING (CHECK POINT)

The unit does not operate.

● The power main switch is

turned off.

● The circuit breaker is

activated to cut off the power

supply.

● Stoppage of electric current.

● ON timer is set.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold

"00" will be shown on the display. (Picture 1)

4. Press

" 00" will disappear and the air conditioner will turn OFF. The Remote

Control B is memorized. (Picture 2)

Note: 1. Repeat above step to reset Remote Control to be A.

more 2 times

Room Temperature

21°C ~ 43°C

17°C ~ 43°C

Cooling or Heating is abnormally low.

● The filters are blocked with dust.

● The temperature has been set

improperly.

● The windows or doors are opened.

● The air inlet or outlet of the outdoor

unit is blocked.

● The fan speed is too low.

● The operation mode is FAN or DRY.

● POWER SELECTION function is

set 75% or 50% (This function is

depend on remote controller).

button on the Remote Control by the tip of the pencil.

during pushing

. "B" will show on the display and

2. Remote Control A has not "A" display.

3. Default setting of Remote Control from factory is A.