Epson PowerLite 8300i with EasyMP.net module Skrócona instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Oprogramowanie Epson PowerLite 8300i with EasyMP.net module. Epson PowerLite 8300i with EasyMP.net module 20 stron. Release of check tool for network projectors v1.00 for windows
Również dla Epson PowerLite 8300i with EasyMP.net module: Podręcznik użytkownika (42 strony), Instrukcja obsługi (36 strony), Instrukcja obsługi (47 strony), Szybka konfiguracja (2 strony), Biuletyn wsparcia produktu (27 strony), Lista części (1 strony), Podręcznik uzupełniający (2 strony), Broszura i specyfikacje (2 strony), Podręcznik użytkownika (1 strony), Biuletyn wsparcia produktu (25 strony), Biuletyn wsparcia produktu (22 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (41 strony), Biuletyn wsparcia produktu (34 strony), Biuletyn wsparcia produktu (28 strony), Biuletyn wsparcia produktu (15 strony), Biuletyn wsparcia produktu (22 strony), Szybka konfiguracja (2 strony)

Drukuj stronę

Epson PowerLite 8300i with
EasyMP.net module Skrócona instrukcja obsługi

EPSON PowerLite 8300i Projector

Previewing Image Sources

You can use the Preview function to help you select the image

source.

1. Press

on the remote control.

Preview

You see the currently selected source displayed in the main

window, as shown below. All other sources (including the

currently selected source) are displayed in smaller preview

windows on the right side and at the bottom. If no

equipment is connected to a port, or if there is no incoming

signal, the preview window for that source appears blank.

Note: Movies are displayed as still images on the preview

screen.

Currently selected source

2. Press one of the

Source

switch to the desired source. Or press

preview screen without switching sources.

Note: A red highlight surrounds the preview window for the

currently selected source. You can use the

the remote control to highlight a different source, and then press

to display it.

Enter

EPSON PowerLite 8300i Projector

Preview windows

buttons on the remote control to

to exit the

ESC

pointer button on

Troubleshooting Display Problems

Follow these guidelines if you're having trouble displaying an

image.

You Can't Project an Image

If you see a blank screen or a blue screen with the

message, try the following:

Make sure the cables are connected correctly.

Make sure the power light is green and not flashing and the

lens cover is off.

If you've connected more than one computer and/or video

source, you may need to press one of the

the projector's control panel or the remote control to select

the correct source. (Allow a few seconds for the projector to

sync up after pressing the button.)

If you're using a PC laptop, press the function key on your

keyboard that lets you display on an external monitor. It

may be labeled

CRT/LCD

You may have to hold down the

Allow a few seconds for the projector to sync up after

changing the setting.

The Projector and Laptop Don't Display the

Same Image

If you're projecting from a laptop, and you don't see the same

image on the projection screen and on your computer screen,

follow these guidelines.

If you're using a PC laptop:

On most systems, there's a function key that lets you toggle

between the LCD screen and the projector, or display on

both at the same time. It may be labeled

an icon such as

key while pressing it. Allow a few seconds for the projector

to sync up after changing the setting.

If the function key doesn't permit you to display

simultaneously on both screens, you should check your

monitor settings to make sure both the LCD screen and the

external monitor port are enabled.

From the Control Panel, open the

Display Properties dialog box, click the

click

. The method for adjusting the settings

Advanced

varies by brand; you may need to click a

make sure the external Monitor port is set as your primary

display and/or enabled. See your computer's

documentation or online help for details.

5/03

No Signal

Source

or have an icon such as

key while pressing it.

CRT/LCD

. You may have to hold down the

utility. In the

Display

Settings

Monitor

buttons on

or with

tab, then