Toshiba e-Studio 1057 Skrócona instrukcja obsługi - Strona 19
Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Wszystko w jednej drukarce Toshiba e-Studio 1057. Toshiba e-Studio 1057 37 stron. Digital multifunctional system
Drukuj stronę
Staple
(When a finisher installed)
This function staples the loaded paper sheets into a sheaf.
1 staple in back
1 staple in front
2 Staples
Setting the number of
copies (number of pages)
Copies/Pages
This function loads previously sorted sheets and outputs multiple
sets at once.
Number of copies setting
1
(1-999)
Enter the number of output copies
(from 1 to 999)
Number of pages setting
Select this to set all pages as one set
If this setting is enabled, set the [Number
*
All Pages
of Copies] to "1".
Select this to specify the number of page for
Manual
each set
Enter a numeric value when [Manual] is
1
(1-200)
selected.
(from 1 to 200 pages)
MANUAL FINISHING
Saddle Stitch
(When a saddle finisher is installed)
This function staples each set of copies at two positions in the
center of paper, folds them in half, and outputs them.
(When a trimming module is installed on the saddle finisher)
For saddle stitch, it trims a side drop, offering a good-looking output
image.
Staples each set of copies at two positions
in the center of paper, and folds them in half
Saddle
during output
Stitch
Trims a side drop for saddle folding during
output
Trimmer
Specify the trimming width within the range of
Setting
2.0 to 20.0 mm
Middle
Checking and changing
tray
the output tray
Offset
Tray
The output tray is automatically selected based on the output
function you set. If Z-Fold, Half Fold, or Punch is selected, however,
you can select the middle or offset tray for the output tray.
If you have changed the output tray, the output function may be
deselected depending on the original output settings.
Middle
Selects the middle tray as the output tray
tray
Offset
Selects the offset tray as the output tray
Tray
Punch function
(When a punch module is installed)
This function punches holes in paper. It is available for paper sizes 8-1/2"x11"R to 11"x17".
You cannot use 12" x 18" (A3W) size paper, and special media such as transparency film.
Punches holes during output
2 Hole Punch
This function can be used with the Z-Fold function if a folding unit is attached to a finisher (100-sheet stapling) or saddle
finisher (100-sheet stapling) while the paper size is 11" x 17", or A3, B4.
3 Hole Punch
Folding function
(When a folding unit is installed)
This function folds paper in Z-fold, C-fold, or other types of shapes.
(When a saddle finisher is installed)
Paper can be folded in a saddle fold.
*
The paper sizes that can be selected vary depending on the type
of paper fold.
Special media such as transparency film and tab paper cannot be
*
used.
Allowable paper sizes:
12"x18", 11"x17", 8-1/2"x14", 8-1/2"x11"R, 8K,
A3W, A3, B4, A4R, SRA3
The fold settings can be configured in [Detail].
Saddle
Fold
B5R can be used only in a saddle finisher
(50-sheet stapling).
Allowable paper sizes:
11"x17", 8-1/2"x14", 8-1/2"x11"R, A3, B4, A4R
This function can be used with the staple and
punch functions if a folding unit is installed in a
Z-Fold
finisher (100-sheet stapling) or saddle finisher
(100-sheet stapling) while the paper size is 11"
x 17", or A3, B4.
Allowable paper sizes:
8-1/2"x11"R, A4R
C-Fold
Allowable paper sizes:
8-1/2"x11"R, A4R
Accord-
ion Fold
Allowable paper sizes:
8-1/2"x11"R, A4R
Double
Fold
Allowable paper sizes:
8-1/2"x11"R, A4R
Half
Fold
19