Philips AZ-2040 Podręcznik użytkownika - Strona 7

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla System stereo Philips AZ-2040. Philips AZ-2040 9 stron. Cd soundmachine
Również dla Philips AZ-2040: Podręcznik użytkownika (15 strony), Podręcznik użytkownika (12 strony), Podręcznik (8 strony), Instrukcja serwisowa (34 strony), Podręcznik (10 strony), (Szwedzki) Snabbmanual (8 strony)

Philips AZ-2040 Podręcznik użytkownika
English
TOP AND FRONT PANELS
(See 1)
1SOURCE – selects CD/ TUNER / TAPE function
2y – power on/ off switch
3Display – shows the status of the set
4Cassette recorder keys
RECORD 0 – starts recording
PLAY 2 – starts playback
SEARCH 5/6 – fast winds/rewinds tape
STOP 9 – stops tape
PAUSE ; – pauses playback or recording
5BASS, MID, HIGH – EQ keys to adjust the bass,
mid & treble frequencies
6PROG
CD:
programs tracks and reviews the program;
Tuner: programs preset radio stations
Navigation controls
7∞, §
CD:
– searches back and forward within a
track;
– skips to the beginning of a current
track/ previous/ later track
Tuner: – tunes to radio stations (down, up).
82; – starts or pauses CD playback
99 – stops CD playback;
– erases a CD program
0MODE – selects different play modes:
e.g.
or
(random) order
REPEAT
SHUFFLE
!Door – lift at the respective door to open cassette/
tape or cd compartment
@VOLUME – to adjust volume level
#REMOTE SENSOR (for AZ2045 model only) –
infrared sensor for remote control
$PRESET DOWN/ UP (–, +) – selects a preset
tuner station (down, up)
%BAND – selects waveband
^DBB – (Dynamic Bass Boost) activates a more
vivid bass response
BACK PANEL
&Telescopic aerial – improves FM reception
*Battery compartment – for 6 batteries,
type R-20, UM1 or D-cells
CONTROLS
(Voltage selector (inside battery compartment,
some versions only) – adjust to match the local
voltage 110/220V before plugging in the set
)p – 3.5 mm stereo headphone socket
Note: The speakers will be muted when
headphones are connected to the set.
¡AC MAINS – inlet for mains lead
REMOTE CONTROL (for AZ2045 only)
1CD – selects CD sound source
2y – switches the set off
Note: When the set is switched off, the remote
control cannot operate any commands.
The set needs to be switched on first via the set's
y button.
3VOLUME 3,4 – adjusts volume level (up, down)
4SHUFFLE – plays all CD tracks in random order
5BASS – selects DBB on/off
62; – starts/ pauses CD playback
7SEARCH 5, 6 – searches backwards/ forwards
within a track
8BAND – selects FM/ MW (AM) waveband
9PRESET +, – – selects a preset radio station
(up, down)
0TUNING ∞, § – tunes to tuner stations
(down, up)
!TUNER – selects tuner sound source
@9 – stops CD playback;
– erases a CD program
#¡, ™ – skips to the beginning of a current track
previous/ subsequent track
$MUTE – interrupts/ resumes sound
%REPEAT – repeats a track /program/ entire CD
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
POWER SUPPLY
Whenever convenient, use the power supply to
conserve battery life. Make sure you remove the
power plug from the set and wall outlet before
inserting batteries.
BASIC FUNCTIONS
Batteries (not included)
• Insert 6 batteries, type R-20, UM-1 or D-cells,
(preferably alkaline) with the correct polarity.
Remote control (for AZ2045 only)
• Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline). (see A)
Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Power
1 Check if the power supply, as shown on the type
plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service centre.
2 If your set is equipped with a voltage selector,
adjust the selector so that it matches with the
local mains.
3 Connect the mains lead to the wall socket.
4 To disconnect the mains supply, unplug the set
from the wall socket.
Auto-Standby mode
When a CD or tape has reached the end of playback
and remains in the stop position for more than
15 minutes, the set will switch off automatically to
save power.
The type plate is located on the bottom of the
set.
BASIC FUNCTIONS
Switching on and off and selecting function
1 Press y on the set to switch on.
2 Press SOURCE once or more to select:
,
CD
or
function.
TAPE
3 Press y to switch off the set.

DIGITAL TUNER

Notes:
– To change from
to
or
TAPE
TUNER
when you are switching off the set: first, make
sure you press the tape STOP 9 key to end
playback and all the cassette keys are released.
– The tone, sound settings, tuner presets and the
volume level (up to a maximum volume level of 20)
will be retained in the set's memory.
Adjusting volume and sound
1 Adjust the volume with the VOLUME control.
™ Display shows the volume level and a number
from 0-32. (See 2)
2 Press DBB once or more to select dynamic bass
boost on or off.
™ Display: shows
when activated.
3 To adjust the bass, mid and treble tones, press and
hold + or – on the BASS, MID, HIGH keys until
you reach the desired level, –5 to +5.
™ Display briefly shows
,
BASS
MID
level. (See 3)
Note: To prevent sound interference the bass control
options operate exclusively. You cannot combine the
bass from BASS with DBB
™ The display shows
or the
is automatically switched off to remind you if you
attempt to use both bass settings
Mute (for AZ2045 only)
1 Press MUTE on the remote control to interrupt
sound reproduction instantly.
™ Playback continues without sound and the
display flashes
.
2 To reactivate sound reproduction you can:
– press MUTE again;
– adjust the volume controls;
– change source.
DIGITAL TUNER
Tuning to radio stations
1 Press y to on, then press SOURCE to select
.
TUNER
is displayed briefly and then the radio station
TU
frequency, waveband and, if programmed, a
TUNER
preset number are shown. (See 4)
2 Press BAND once or more to select your
waveband.
function, or
CD
, or
and the
HIGH
indicator