Toshiba TLP-S10 Instrukcja obsługi - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Projektor Toshiba TLP-S10. Toshiba TLP-S10 22 stron. 1,200 ansi-lumens 2.1 kg eco mode
Również dla Toshiba TLP-S10: Instrukcja obsługi (22 strony), Specyfikacje (2 strony), Instrukcja serwisowa (33 strony)

Drukuj stronę
Toshiba TLP-S10 Instrukcja obsługi
Using handy features (Continued)
I Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the
button twice (or press the CALL button on the remote
control once).
When the
button is pressed once, the Setting
display menu appears. Pressing it again displays
information
. The table below shows what kind
p.29
of information is displayed. Press the
press the CALL or CANCEL button on the remote
control to serve the same purpose) again to
dismiss the display.
Item
Description
Input
Input source name
RGB signal mode RGB input mode
H-resolution
Horizontal resolution (in bits)
V-resolution
Vertical resolution (in bits)
H-frequency
Horizontal sync frequency
V-frequency
Vertical sync frequency
Sync
Sync signal polarity
Signal format
Y/P
/P
signal format
B
R
Video mode
Color method of video signal
Lamp time
Time of lamp use
Version
Firmware version
Notes
1: The mode of supported RGB signals
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a store about getting a TLPLV3 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector's internal control program. This version is
referred to for customer service, etc.
Notes
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
Remote
Control panel
Control
FAN TEMP LAMP
ON
CALL
INPUT
ON / STANDBY
KEYSTONE
+
ZOOM
button (or
MUTE
MENU
-
+
VOL.
VOL.
CANCEL
KEYSTONE
AUTO SET
-
ZOOM
"Yes": displayed, "No": not displayed
Computer Y/P
/P
Video
B
R
Yes
Yes
Yes
[Note 1]
Yes
No
No
Yes
No
No
Yes
No
No
Yes
No
No
[Note 2]
Yes
No
No
[Note 3]
Yes
No
No
No
Yes
No
No
No
Yes
[Note 4]
Yes
Yes
Yes
[Note 5]
Yes
Yes
Yes
is shown.
p.38
28

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons
I How to use the menus
The menu shown below is only for operation instructions and might be different from the
actual display.
ON/
STANDBY
2. Select a Category
AUTOSET
FREEZE
Select a category by using
RESIZE
There are following three
categorys.
INPUT
Image adjustment menu
Default setting menu
S-video
Display setting menu
Yes
No
No
No
3. Adjustments & Settings
No
No
No
Adjustment/Setting Value
No
Yes
Yes
These marks signify the
Yes
items can be adjusted/set
by using
These marks signify an
item can be switched by
using
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
These marks signify the items can be selected from
the list by using
After an item is selected, apply it by pressing
4. Back
Note
• Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
• You can also use the CANCEL button on the remote control to dismiss the menu display.
on the control panel (main unit side) and remote control.
p.16
1. Start
Display the Setting display menu
.
p.30
p.30
p.31
Press
to open the menu
of the selected category.
Item
This mark signfy that
.
there are options.
Press
to display a
list of options.
.
.
.
29
Displays the current
adjustments of selected
category.
Item shown with gray
cannot be adjusted with
the current input source.
5. To Finish
Finish via the Status
display menu.
To Status display
p.28
6. End
The menu disappears.