Dimplex 6909590100 Instrukcja serwisowa - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja serwisowa dla Grzałka Dimplex 6909590100. Dimplex 6909590100 17 stron.

Drukuj stronę

PREPARATION FOR SERVICE

NOTE: All components are replaceable from the front of

the fireplace while the unit is mounted on the wall, with the

exception of replacement of the power cord.

NOTE: If the power cord needs replacing or if the unit

needs to be removed from the wall for any other reason

please begin service by following the "PREPARATION FOR

SERVICE" instructions, then move on to the section "IN-

STRUCTIONS FOR REMOVING FROM WALL".

Tools Required: Phillips head screwdriver

WARNING: Disconnect power before attempting any

maintenance or cleaning to reduce the risk of electric

shock or damage to persons.

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights and heating elements to cool

off to avoid accidental burning of skin.

1. Disconnect power source.

•

Unplug the fireplace from the outlet.

•

If unit has been hard wired for power or outlet is

not accessible from the front, turn the breaker off at

the electrical panel.

2. Remove the front glass assembly by removing the 2

screws (1 on the left and 1 on the right side). These

screws secure the front glass panel to the inside of the

fireplace. (Figure 4)

3. Lift the front glass assembly off of the 4 mounts located

between the outer and inner casing of the fireplace: 2

on the left and 2 on the right. (Figure 3) Carefully place

the glass assembly aside in a safe location.

4. Proceed to the instructions within this manual relating

to the repair being performed - see Table of Contents

for page number.

INSTRUCTIONS FOR REMOVING FROM

WALL

NOTE: Only required for replacement of the

power cord or removal from service.

WARNING: Disconnect power before attempting any

maintenance or cleaning to reduce the risk of electric

shock or damage to persons.

CAUTION: If unit was operating prior to servicing allow

at least 10 minutes for lights and heating elements to cool

off to avoid accidental burning of skin.

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

Mounting - The fireplace may be mounted in one of 3 meth-

ods:

•

Surface Mount

•

Recess Mount - Partial In-Wall

•

Flush Mount (completely in the wall)

Identify the type of mounting and follow the appropriate

instructions in the following pages.

CAUTION: To prevent injury or damage, turn off the

breaker in your electrical panel prior to attempting to re-

Figure 3

Front glass

assembly

Mounts (4)

Hooks (4)

Figure 4

move this unit off the wall.

NOTE: If fireplace is hard wired directly to the electrical

panel, and there is not enough slack in the wires within the

wall to reach your work area, remove the electrical junction

box cover located on the bottom right by removing the 2

screws on the front of the cover. Lift the cover off and set

aside. Disconnect the 3 wire connectors connected to the

power source, taking note of their original configuration

• Line: Red wire from unit to the line wire power source

• Neutral: Thin white wire and thick blue wire to neutral

wire from power source

• Thin black wire and thick white wire are left connect-

ed and not changed.

Surface Mount

(Figure 6)

Tools Required: Phillips head screwdriver

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove the decorative acrylic ember-bed pieces from

the media tray, which lies along the bottom of the interi-

or Partially Reflective Glass. A medium sized container

such as a bucket or a box will be needed to keep the

acrylic ember-bed pieces together.

2. On the bottom of the unit remove the securing screw

from the L-bracket. (Figure 5)

3. Lift the unit up and off of the wall.

4. Carefully lay the unit down on a solid flat surface with

the front of the unit facing up.

Front tray

Tab