Dimplex XMX712N Instrukcja instalacji i obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Grzałka Dimplex XMX712N. Dimplex XMX712N 4 stron. Xms(n) automatic xmx(n) storage heater range

Drukuj stronę

THE FOLLOWING MUST BE APPLIED WHEN

FIXING THE HEATER TO THE WALL BRACKET

i) If no skirting board is present secure the heater through

the wall bracket slots closest to the wall.

ii) If 100mm (4in.) skirting is present secure the heater

through the outer slots.

iii) If skirting taller than 150mm (6in.) is present this must be

reduced to 150mm (6in.) over the entire width of the heater

plus 25mm (1in.) at each end.

Do not fully tighten these screws until the bricks are loaded

into the heater as some settling of the heater may occur.

NOTE: NEVER REMOVE THESE SCREWS WITHOUT

FIRST UNLOADING THE HEATER.

Remove the front panel by removing the two self tapping

screws along its bottom edge. With hands positioned on

each side of the panel, lift upwards to unhook the top edge

whilst pressing down on the top panel with your thumbs. The

panel can now be lifted clear and set to one side.

Remove the inner front by removing the screws along its

top and sides. As the front insulation is attached care must

be taken when lifting this panel from the heater and placing it

to one side. Remove the internal packing by sliding it up and

off the elements taking care not to damage the insulation.

Remove one element to allow access for the back rows

of bricks. On the 724N remove the element to the right

of centre, on the 718N remove the central element, on the 712N

the left hand element should be removed and, on the 706N, there

is only one element.

Loosen the two screws securing the element tails in the ceramic

connector block, and lift the element up and out of the heater.

10.

Carefully ﬁ t the bottom row of the back layer of bricks

placing the two end bricks in position ﬁ rst with the re-

cess towards the element. Fit the top row of bricks also with

the recess towards the element.

11.

Reﬁ t the element which has been removed by feeding

the tails down through the hole in the base insulation and

into the connector block. Ensure the element is fully pushed

home then securely tighten the two screws in the block.

11.

12.

Fit the front layer of bricks again with the recess towards

the element. The complete core will comprise:

706N - 1 x 4 Brick Columns

712N - 2 x 4 Brick Columns

718N - 3 x 4 Brick Columns

724N - 4 x 4 Brick Columns

13.

Replace the inner front complete with insulation by

locating its bottom edge behind the front lip of the

chassis and inserting retaining screws along the top and

both sides.

14.

For models 712N, 718N and 724N only, check that the

ﬂ ap mechanism operates freely on its hinges and that

with the output control set to 1 the ﬂ ap is correctly seated in

its closed position.

15.

Feed the mains cable through the cable clamp and

make connections as marked on heater. Pull back any

slack through the clamp and tighten clamping screw.

WARNING - This appliance must be earthed

15.

16.

Replace outer front panel and grille by hooking the grille

into its retaining slot on the top panel and lowering it

into position. Secure the front panel with the two self tapping

screws.

16.

17.

Check that the screws securing the heater to the wall

bracket have been fully tightened.

IT IS ESSENTIAL THAT ALL SCREWS ARE REPLACED

TO ENSURE EARTH CONTINUITY.

Once installed do not attempt to reposition the heater without

ﬁ rst obtaining the services of a competent electrician.