Pioneer AVH-P5900DVD Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik samochodowy Pioneer AVH-P5900DVD. Pioneer AVH-P5900DVD 9 stron. Pioneer avh-p5900dvd: install guide
Również dla Pioneer AVH-P5900DVD: Instrukcja instalacji (5 strony), Instrukcja serwisowa (16 strony)

Drukuj stronę

AVH-P5900DVD

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<CRD4214-A/N> UC

Connecting the Units

WARNING

CAUTION

• To avoid the risk of accident and the potential vio-

lation of applicable laws, the front DVD or TV

• PIONEER does not recommend that you

(sold separately) feature should never be used

install or service your display yourself.

while the vehicle is being driven. Also, Rear

Installing or servicing the product may

Displays should not be in a location where it is a

expose you to risk of electric shock or

visible distraction to the driver.

other hazards. Refer all installation and

• In some countries or states the viewing of

images on a display inside a vehicle even by

servicing of your display to authorized

persons other than the driver may be illegal.

Pioneer service personnel.

Where such regulations apply, they must be

• Secure all wiring with cable clamps or

obeyed and this unit's DVD features should

not be used.

electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not drill a hole into the engine com-

partment to connect the yellow lead of

the unit to the vehicle battery. Engine

vibration may eventually cause the insu-

lation to fail at the point where the wire

passes from the passenger compartment

into the engine compartment. Take extra

care in securing the wire at this point.

• It is extremely dangerous to allow the

display lead to become wound around

the steering column or gearshift. Be sure

to install the display in such a way that it

will not obstruct driving.

• Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, parking brake or seat slid-

ing mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work prop-

erly.

WARNING

LIGHT GREEN LEAD AT POWER CONNEC-

TOR IS DESIGNED TO DETECT PARKED

STATUS AND MUST BE CONNECTED TO

THE POWER SUPPLY SIDE OF THE PARK-

ING BRAKE SWITCH. IMPROPER CONNEC-

TION OR USE OF THIS LEAD MAY VIOLATE

APPLICABLE LAW AND MAY RESULT IN

SERIOUS INJURY OR DAMAGE.

ENGLISH

Note:

•

Control signal is output through blue/white cable

•

This unit cannot be installed in a vehicle with-

when this unit is powered on. Connect it to an

out ACC (accessory) position on the ignition

external power amp's system remote control or

switch.

the vehicle's auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

•

Never connect blue/white cable to external power

amp's power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

•

IP-BUS connectors are color-coded. Be sure to

ACC position

No ACC position

connect connectors of the same color.

•

Use this unit in other than the following condi-

•

Black cable is ground. This cable and other prod-

tions could result in fire or malfunction.

uct's ground cable (especially, high-current prod-

— Vehicles with a 12-volt battery and negative

ucts such as power amp) must be wired separate-

grounding.

ly. Otherwise, fire or malfunction may result if

— Speakers with 50 W (output value) and 4 ohm

they are accidentally detached.

to 8 ohm (impedance value).

•

Cord function may differ according to the

•

To prevent short-circuit, overheating or malfunc-

product, even if cord color is the same. When

tion, be sure to follow the directions below.

connecting this system, be sure to check all

— Disconnect the negative terminal of the battery

manuals and connect cords correctly.

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive

tape around them where they lie against metal

parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not remove RCA caps if RCA cables are

not used.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's nega-

tive cables.