Pioneer AVX-P8DVD Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik samochodowy Pioneer AVX-P8DVD. Pioneer AVX-P8DVD 9 stron. Owner's manual
Również dla Pioneer AVX-P8DVD: Instrukcja obsługi (34 strony), Instrukcja obsługi (4 strony)

Drukuj stronę

AVX-P8DVD

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD3865-A> UC

Connecting the Units

CAUTION:

WARNING:

• PIONEER does not recommend that you

• To avoid the risk of accident and the

install or service your display yourself.

potential violation of applicable laws, the

Installing or servicing the product may

front DVD or TV (sold separately) fea-

expose you to risk of electric shock or

ture should never be used while the vehi-

other hazards. Refer all installation and

cle is being driven. Also, Rear Displays

servicing of your display to authorized

should not be in a location where it is a

Pioneer service personnel.

visible distraction to the driver.

• Secure all wiring with cable clamps or

• In some countries or states the viewing of

electrical tape. Do not allow any bare

images on a display inside a vehicle even

wiring to remain exposed.

by persons other than the driver may be

illegal. Where such regulations apply,

• Do not drill a hole into the engine com-

they must be obeyed and this unit's DVD

partment to connect the yellow lead of

features should not be used.

the unit to the vehicle battery. Engine

vibration may eventually cause the insu-

lation to fail at the point where the wire

passes from the passenger compartment

into the engine compartment. Take extra

care in securing the wire at this point.

• It is extremely dangerous to allow the

display lead to become wound around

the steering column or gearshift. Be sure

to install the display in such a way that it

will not obstruct driving.

• Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, parking brake or seat slid-

ing mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work prop-

erly.

Note:

• To prevent incorrect connection, the input side of

• This unit is for vehicles with a 12-volt battery and

the IP-BUS connector is blue, and the output side

negative grounding. Before installing it in a recre-

is black. Connect the connectors of the same

ational vehicle, truck, or bus, check the battery

colors correctly.

voltage.

• If this unit is installed in a vehicle that does not

• To avoid shorts in the electrical system, be sure to

have an ACC (accessory) position on the ignition

disconnect the ≠ battery cable before beginning

switch, the red lead of the unit should be connected

to a terminal coupled with ignition switch ON/OFF

installation.

operations. If this is not done, the vehicle battery

• Refer to the owner's manual for details on

may be drained when you are away from the vehi-

connecting the power amp and other units, then

make connections correctly.

cle for several hours. (Fig. 1)

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

ACC position

No ACC position

• Don't pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Cords for this product and those for other products

• Never feed power to other equipment by cutting

may be different colors even if they have the same

the insulation of the power supply lead of the unit

function. When connecting this product to another

and tapping into the lead. The current capacity of

product, refer to the supplied manuals of both

the lead will be exceeded, causing overheating.

products and connect cords that have the same

• When replacing fuse, be sure to use only fuse of

function.

the rating prescribed on the fuse holder.

• If the RCA pin jack on the unit will not be used, do

not remove the caps attached to the end of the con-

nector.

Fig. 1