Pioneer DEH-1100MP Instrukcja instalacji - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik samochodowy Pioneer DEH-1100MP. Pioneer DEH-1100MP 8 stron. Cd rds receiver
Również dla Pioneer DEH-1100MP: Broszura (9 strony), Instrukcja obsługi (24 strony)
Drukuj stronę
Connections
4 Note:
19 Rear output
1 This product
Depending on the kind of vehicle, the function
(DEH-1120MP/DEH-1100MPB/
of 3* and 5* may be different. In this case, be
DEH-1100MP)
sure to connect 2* to 5* and 4* to 3*.
1*
3*
2*
2 Antenna jack
3 Fuse (10 A)
5*
4*
6 Cap (1*)
5 Connect leads of the same
Do not remove cap if this
color to each other.
terminal is not in use.
7 Yellow (3*)
8 Yellow (2*)
Back-up
Connect to the constant 12 V supply
(or accessory)
terminal.
9 Red (5*)
10 Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
13 Speaker leads
In some vehicles, the ISO connector may be
White: Front left
divided into two. In this case, be sure to
White/black: Front left
connect to both connectors.
Gray: Front right
Gray/black: Front right
Green: Rear left
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
En
Connections
20 This diaglam is for DEH-1120MP/DEH-1100MPB/DEH-1100MP .
23 Power amp
(sold separately)
21 To Rear output
22 Connect with RCA cables
14 Wired remote input
(sold separately)
Hard-wired remote control adaptor
can be connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
24 System remote control
17 Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will
25 Left
26 Right
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
27 Rear speaker
27 Rear speaker
antenna control type. In another type of
vehicle, never connect 6* and 7*.
28 Perform these connections when using
the optional amplifier.
En
Connections
— Never band together multiple speaker's ne-
Important
gative cables.
! When this unit is installed in a vehicle without
! Control signal is output through blue/white
ACC (accessory) position on the ignition
cable when this unit is powered on. Connect it
switch, red cable must be wired to the term-
to an external power amp's system remote
inal that can detect the operation of the igni-
control or the vehicle's auto-antenna relay
tion key. Otherwise, battery drain may result.
control terminal (max. 300 mA 12 V DC). If the
vehicle is equipped with a glass antenna, con-
nect it to the antenna booster power supply
terminal.
! Never connect blue/white cable to external
power amp's power terminal. Also, never con-
ACC position
No ACC position
nect it to the power terminal of the auto anten-
! Use of this unit in conditions other than the
na. Otherwise, battery drain or malfunction
following could result in fire or malfunction.
may result.
— Vehicles with a 12-volt battery and negative
! Black cable is ground. This cable and other
grounding.
product's ground cable (especially, high-cur-
— Speakers with 50 W (output value) and 4
rent products such as power amp) must be
ohm to 8 ohm (impedance value).
wired separately. Otherwise, fire or malfunc-
! To prevent a short-circuit, overheating or mal-
tion may result if they are accidentally de-
function, be sure to follow the directions
tached.
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or ad-
Connection Diagram (Fig. 1)
hesive tape. To protect the wiring, wrap ad-
hesive tape around them where they lie
1 This product
against metal parts.
2 Antenna jack
— Place all cables away from moving parts,
3 Fuse (10 A)
such as gear shift and seat rails.
4 Note:
— Place all cables away from hot places,
Depending on the kind of vehicle, the function
such as near the heater outlet.
of 3* and 5* may be different. In this case, be
— Do not pass the yellow cable through a
sure to connect 2* to 5* and 4* to 3*.
hole into the engine compartment to con-
5 Connect leads of the same color to each
nect to a battery.
other.
— Cover any disconnected cable connectors
6 Cap (1*)
with insulating tape.
Do not remove cap if this terminal is not in
— Do not shorten any cables.
use.
Fig. 1
— Never cut the insulation of the power cable
7 Yellow (3*)
Abb. 1
of this unit in order to share the power
Back-up (or accessory)
Afb. 1
with other devices. Current capacity of the
8 Yellow (2*)
Рис. 1
cable is limited.
Connect to the constant 12 V supply terminal.
— Use a fuse of the rating prescribed.
9 Red (5*)
— Never wire the speaker negative cable di-
Accessory (or back-up)
rectly to ground.
En
Connections
10 Red (4*)
24 System remote control
Connect to terminal controlled by ignition
25 Left
switch (12 V DC).
26 Right
11 Black (chassis ground)
27 Rear speaker
Connect to a clean, paint-free metal location.
28 Perform these connections when using the
12 ISO connector
optional amplifier.
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
13 Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (7*)
Connect to auto-antenna relay control term-
inal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will dif-
fer depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
19 Rear output (DEH-1120MP/DEH-1100MPB/
DEH-1100MP)
20 This diagram is for DEH-1120MP/DEH-
1100MPB/DEH-1100MP .
21 To Rear output
22 Connect with RCA cables (sold separately)
23 Power amp (sold separately)
En