Pioneer DEH-5400BT Instrukcja obsługi - Strona 13

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odbiornik samochodowy Pioneer DEH-5400BT. Pioneer DEH-5400BT 25 stron. Cd rds receiver

Drukuj stronę

Operating this unit

Press M.C. and hold until the customizing

illumination color setting appears in the dis-

play.

Press M.C. to select the primary color.

R (red) G (green) B (blue)

Turn M.C. to adjust the brightness level.

Adjustment range: 0 to 60

You cannot select a level below 10 for all three of

R (red), G (green), and B (blue) at the same time.

You can also perform the same operation on

other colors.

Notes

You cannot create a custom illumination

color when SCAN or a set of colors (WARM,

AMBIENT, or CALM) is selected.

You can create custom illumination colors

for both KEY COLOR and DISP COLOR.

Switching the dimmer setting

You can adjust the brightness of illumination.

Press and hold

Using an AUX source

Insert the stereo mini plug into the AUX

input jack.

Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on page 11.

Turning the clock display on

or off

Press

to turn the clock display on or

off.

The clock display disappears temporarily when

you perform other operations, but the clock display

appears again after 25 seconds.

Installation

Connections

WARNING

Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do

not use 1 W to 3 W speakers for this unit.

The black cable is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire first.

Ensure that the ground wire is properly con-

nected to metal parts of the car s body. The

ground wire of the power amp and the one of

this unit or any other device must be con-

nected to the car separately with different

screws. If the screw for the ground wire loos-

ens or falls out, it could result in fire, genera-

tion of smoke or malfunction.

POWER AMP

Ground wire

Other devices

Metal parts of car's body

(Another electronic

device in the car)

Important

When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position

No ACC position

Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may re-

sult in a fire or malfunction.

To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

Disconnect the negative terminal of the bat-

tery before installation.

Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

Place all cables away from moving parts,

such as the shift lever and seat rails.

Place all cables away from hot places, such

as near the heater outlet.

Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

Cover any disconnected cable connectors

with insulating tape.

Do not shorten any cables.

Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

Use a fuse of the rating prescribed.

Never wire the negative speaker cable directly

to ground.

Never band together negative cables of multi-

ple speakers.

When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

Section