Pioneer DVH-P500UB Instrukcja instalacji

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik Pioneer DVH-P500UB. Pioneer DVH-P500UB 8 stron. Dvd rds receiver

Drukuj stronę

DVH-P500UB

Printed in Thailand

ç‡ÔÂ˜‡Ú‡ÌÓ ‚ í‡ËÎ‡Ì‰Â

<CRD4326-A/N> RE

Connecting the Units

Note:

•

Control signal is output through blue/white cable

•

When this unit is installed in a vehicle without

when this unit is powered on. Connect it to an

ACC (accessory) position on the ignition switch,

external power amp's system remote control or

red cable must be wired to the terminal that can

the vehicle's auto-antenna relay control terminal

detect the operation of the ignition key.

(max. 300 mA, 12 V DC). If the vehicle is

Otherwise, battery drain may result.

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

•

Never connect blue/white cable to external power

amp's power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

•

IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

•

Black cable is ground. This cable and other prod-

ACC position

No ACC position

uct's ground cable (especially, high-current prod-

•

Use this unit in other than the following condi-

ucts such as power amp) must be wired separate-

tions could result in fire or malfunction.

ly. Otherwise, fire or malfunction may result if

— Vehicles with a 12-volt battery and negative

they are accidentally detached.

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

•

To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive

tape around them where they lie against metal

parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not remove RCA caps if RCA cables are

not used.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's nega-

tive cables.

Power cable connection

Note:

Depending on the kind of vehicle, the

function of 3* and 5* may be different. In

this case, be sure to connect 2* to 5* and 4*

Antenna jack

to 3*.

15 cm

Connect leads of the same

color to each other.

Cap (1*)

Do not remove cap if

Fuse (10 A)

this terminal is not in

use.

Yellow (3*)

Yellow (2*)

Back-up (or

Connect to the constant

accessory)

12 V supply terminal.

Fuse resistor

Red (5*)

Red (4*)

Accessory

Connect to terminal controlled

(or back-up)

by ignition switch (12 V DC).

Black (chassis ground)

Connect to a clean, paint-free metal location.

Speaker leads

Note:

White:

Front left

In some vehicles, the ISO connector

White/black: Front left

may be divided into two. In this case,

Gray:

Front right

be sure to connect to both connectors.

Gray/black: Front right

Green:

Rear left

or subwoofer

When you connect the separately sold multi-channel

Green/black: Rear left

or subwoofer

processor (DEQ-P6600) to this unit, do not connect

Violet:

Rear right

or subwoofer

anything to the speaker leads and system remote

Violet/black: Rear right

or subwoofer

control (blue/white).

AUX jack (3.5 ø)

20 cm

Use a mini plug cable

1.5 m

to connect with

auxiliary device.

USB cable

Connect to separately sold USB device.

15 cm

IP-BUS input

This product

(Blue)

Hard-wired remote control adaptor can be

connected (sold separately).

IP-BUS cable

Multi-CD player

(sold separately)

Yellow/black

If you use an equipment with Mute function, wire

this lead to the Audio Mute lead on that equipment.

If not, keep the Audio Mute lead free of any

connections.

Violet/white

Of the two lead wires connected to the back lamp,

connect the one in which the voltage changes when

the gear shift is in the REVERSE (R) position.

For details, refer to When connecting with a rear

view camera.

Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Notes:

The pin position of the ISO connector will differ

• Change the initial setting of this unit (refer to the

depends on the type of vehicle. Connect 6* and

Operation Manual). The subwoofer output of this

7* when Pin 5 is an antenna control type. In

unit is monaural.

another type of vehicle, never connect 6* and 7*.

• When using a subwoofer of 70 W (2 Ω) , be sure to

connect with Violet and Violet/black leads of this

unit. Do not connect anything with Green and

Green/black leads.