Pioneer XV-HTD510 Instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odbiornik Pioneer XV-HTD510. Pioneer XV-HTD510 48 stron. Dvd receiver/speaker system
Również dla Pioneer XV-HTD510: Instrukcja obsługi (48 strony)

Drukuj stronę

1. Remote Control

IMPORTANT SAFETY INSTRUCTIONS

READ INSTRUCTIONS — All the safety and

operating instructions should be read before

the product is operated.

RETAIN INSTRUCTIONS — The safety and

operating instructions should be retained for

future reference.

HEED WARNINGS — All warnings on the product

and in the operating instructions should be

adhered to.

FOLLOW INSTRUCTIONS — All operating and

use instructions should be followed.

CLEANING — Unplug this product from the wall

outlet before cleaning. The product should be

cleaned only with a polishing cloth or a soft dry

cloth. Never clean with furniture wax, benzine,

insecticides or other volatile liquids since they

may corrode the cabinet.

ATTACHMENTS — Do not use attachments not

recommended by the product manufacturer as

they may cause hazards.

WATER AND MOISTURE — Do not use this

product near water — for example, near a

bathtub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming

pool; and the like.

ACCESSORIES — Do not place this product on an

unstable cart, stand, tripod, bracket, or table.

The product may fall, causing serious injury to

a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod,

bracket, or table recommended by the

manufacturer, or sold with the product. Any

mounting of the product should follow the

manufacturer's instructions, and should use a

mounting accessory recommended by the

manufacturer.

CART — A product and cart combination should be

moved with care. Quick stops, excessive force,

and uneven surfaces may cause the product

and cart combination to overturn.

VENTILATION — Slots and openings in the cabinet

are provided for ventilation and to ensure reliable

operation of the product and to protect it from

overheating, and these openings must not be

blocked or covered. The openings should never

be blocked by placing the product on a bed, sofa,

rug, or other similar surface. This product should

not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is

provided or the manufacturer's instructions have

been adhered to.

POWER SOURCES — This product should be

operated only from the type of power source

indicated on the marking label. If you are not

sure of the type of power supply to your home,

consult your product dealer or local power

company.

LOCATION – The appliance should be installed

in a stable location.

NONUSE PERIODS – The power cord of the

appliance should be unplugged from the

outlet when left unused for a long period of

time.

GROUNDING OR POLARIZATION

If this product is equipped with a polarized

alternating current line plug (a plug having one

blade wider than the other), it will fit into the outlet

only one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit,

contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the

polarized plug.

If this product is equipped with a three-wire

grounding type plug, a plug having a third

(grounding) pin, it will only fit into a grounding type

power outlet. This is a safety feature. If you are

unable to insert the plug into the outlet, contact

your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the grounding

type plug.

POWER-CORD PROTECTION — Power-supply cords

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them, paying particular attention to cords

at plugs, convenience receptacles, and the point

where they exit from the product.

OUTDOOR ANTENNA GROUNDING — If an outside

antenna or cable system is connected to the

product, be sure the antenna or cable system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article

810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper

grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to

grounding electrodes, and requirements for the

grounding electrode. See Figure A.

LIGHTNING — For added protection for this product

during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage

to the product due to lightning and power-line

surges.

POWER LINES — An outside antenna system should

not be located in the vicinity of overhead power

lines or other electric light or power circuits, or

where it can fall into such power lines or circuits.

When installing an outside antenna system,

extreme care should be taken to keep from

touching such power lines or circuits as contact

with them might be fatal.

OVERLOADING — Do not overload wall outlets,

extension cords, or integral convenience

receptacles as this can result in a risk of fire or

electric shock.

ELECTRIC

SERVICE

EQUIPMENT

Fig. A

OBJECT AND LIQUID ENTRY — Never push

objects of any kind into this product through

openings as they may touch dangerous voltage

points or short-out parts that could result in a

fire or electric shock. Never spill liquid of any

kind on the product.

SERVICING — Do not attempt to service this

product yourself as opening or removing covers

may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service

personnel.

DAMAGE REQUIRING SERVICE — Unplug this

product from the wall outlet and refer servicing

to qualified service personnel under the

following conditions:

When the power-supply cord or plug is

damaged.

If liquid has been spilled, or objects have fallen

into the product.

If the product has been exposed to rain or

water.

If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to its normal operation.

If the product has been dropped or damaged in

any way.

When the product exhibits a distinct change in

performance — this indicates a need for service.

REPLACEMENT PARTS — When replacement

parts are required, be sure the service technician

has used replacement parts specified by the

manufacturer or have the same characteristics

as the original part. Unauthorized substitutions

may result in fire, electric shock, or other

hazards.

SAFETY CHECK — Upon completion of any service

or repairs to this product, ask the service

technician to perform safety checks to

determine that the product is in proper operating

condition.

WALL OR CEILING MOUNTING — The product

should not be mounted to a wall or ceiling.

HEAT — The product should be situated away from

heat sources such as radiators, heat registers,

stoves, or other products (including amplifiers)

that produce heat.

GROUND

CLAMP

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC — NATIONAL ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)