Pioneer A-858 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Pioneer A-858. Pioneer A-858 11 stron.

Drukuj stronę

PANEL FACILITIES

See page 2 for Panel Facilities.

[FRONT PANEL]

@ POWER switch/indicator

Press to turn power to the unit ON and OFF.

When the power is ON, indicator lights.

@ PHONES jack

When using headphones, insert the plug into this jack.

@ SPEAKERS selector switch

Use this switch to listen to the speaker systems connected to the

SPEAKERS terminals.

OFF:

Released position: No sound is heard from the speaker system.

Set to this position when listening with headphones.

For reproduction of sound with the speaker systems connected to

the SPEAKERS A terminals.

For reproduction of sound with the speaker systems connected to

the SPEAKERS B terminals.

A+B:

For reproduction of sound with the speaker systems connected to

SPEAKERS A and B terminals.

@ BASS tone control

Use to adjust the low-frequency tone at low volume level. The

center position is the flat (normal) position. When turned to the

right, low-frequency tones are emphasized; when turned to the left,

low-frequency tones are de-emphasized.

NOTE:

This function does not operate when the DIRECT switch is in the

ON position.

Use to adjust the high-frequency tone at low volume level.

The center position is the flat (normal) position. When turned to the

right, high-frequency tones are emphasized; when turned to the

left, high-frequency tones are de-emphasized.

NOTE:

This function does not operate when the DIRECT switch is in the

ON position.

Should normally be left in the center position. Adjust balance if the

sound is louder from one of the speakers. If the right side is louder,

turn toward the LEFT position and if the left side is louder, turn

toward the RIGHT position.

NOTE:

This function does not operate when the DIRECT switch is in the

ON position.

@ PHONO EQ switch/indicator

When not using a phono input, turn the phono equalizer power

circuit off in order to prevent it from collecting noise during

playback of other sources.

ON:

The indicator lights: Always set to this position when using a phono

input. Immediately after turning ON, audio signal will be muted for

several seconds until circuit operation becomes stable.

OFF:

The indicator goes off: Set to this position when not using a phono

input.

LOUDNESS switch/indicator

Use when listening at low volume levels.

ON:

The indicator lights: Boosts low and high frequencies to give added

punch to playback even at low-volume.

OFF:

The indicator goes off: Should normally be left in this position.

NOTE:

This switch does not operate when the DIRECT switch is in the ON

position.

Use this switch to listen to tape playback, or to listen to the sounds

being recorded during tape recording.

ON:

The indicator lights: Press when listening to the playback sound of

the tape deck or the adaptor connected to the ADPT 1/TAPE 3

IN/PLAY terminals, or to monitor the sound being recorded on the

tape deck connected to the ADPT 1/TAPE 3 OUT/REC teminals.

OFF:

The indicator goes off: Normally leave the switch in this position.

NOTE:

When the DIRECT switch is set to ON, this function does not

operate and no signal is output at the ADPT 1/TAPE 3 0UT/REC

terminals.

@ DIRECT switch/indicator

Use this switch when you do not wish to pass the output for input

terminal

equipment

through

the various

frequency adjusting

circuits and adaptor terminals (ADPT 1/TAPE 3, ADPT 2, BASS,

TREBLE, BALANCE, LOUDNESS).

ON:

When the switch is in this position, the indicator lights and the

signals input from the input terminals are reproduced without

passing through the various frequency-adjusting

circuits. This

results in flat, pure sound which is a more faithful reproduction of

the input source.

OFF:

When the switch is in this position the indicator goes ou and the

signal passes through the various frequency adjusting cirwits.

<AREZ 11195