Pioneer VSA-1000 Instrukcja obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wzmacniacz Pioneer VSA-1000. Pioneer VSA-1000 35 stron. Av digital surround amplifier
Również dla Pioneer VSA-1000: Instrukcja obsługi (35 strony)

Drukuj stronę

@ POWER STANDBY/ON switch/indicator

remain on even when the POWER switch is turned off. The unit is

in the standby mode.

*® The indicator lights when the unit is in the standby mode.

* The accessory remote control unit can also be used to turn the

amplifier on or standby (STANDBY function).

* When not using the unit for a long period, disconnect the power cord.

@ SPEAKER switches/indicators

ON/OFF switches for the speaker systems, An indicator lights when

any of these switches is set to ON.

FRONT A, B:

Switches and indicates for the front speaker systems A, B.

REAR:

Switches and indicates for the rear speaker systems.

CENTER:

Switches and indicates for the front center channel speaker system.

® BASS control switches

Use to adjust the low-frequency level. Press the + switch to increase

low-frequency level, and the ~ switch to decrease it.

When

both

sides

(+,

—)} of the

BASS

control

are

pressed

simultaneously, the base response will be set to the flat (normal)

condition.

@ TREBLE control switches

Use to adjust the high-frequency level. Press the + switch to increase

high-frequency level, and the — switch to decrease it.

When

both sides

(+,

-~) of the TREBLE

control are pressed

simultaneously, the treble response will be set to the flat (normal)

condition.

® ACOUSTIC switches (MEMORY, SELECT)

Five types of tone (bass and treble) control settings can be preset.

MEMORY:

Press this switch to store in memory.

SELECT;

Tone setting changes as follows when pressing this switch repeatedly:

FLAT

-»* LOUDNESS

-* Memory A

Memory E~- Memory Dt Memory C~#— Memory ea

FLAT:

Flat toné characteristics.

LOUDNESS:

Low and high frequencies are emphasized. Use this setting to

obtain a full-bodied sound when listening.

Presetting the acoustic memory

1. Adjust the sound quality as desired using the BASS and TREBLE

control switches.

2. Press the MEMORY switch.

3. Press the SELECT switch and select the sign to which you wish

to assign the setting (A — E) while the indicator flashes.

* When

the indicator lights after flasHing, it indicates that the

command has been stored in memory. If you don't select memory

Positions (A —

E) while the ACOUSTIC

indicator is flashing,

nothing will be stored in memory.

FRONT PANEL FACILITIES

* In this way, the desired tone will be preset in one of the five

acoustic memory positions. To preset four other desired tone

settings, perform the same operations.

* To recall the memorized tone settings, press the SELECT switch

to select the desired memory position.

NOTE:

STANDBY position, provided the

power cord is plugged into an AC wail socket, memory will not be

erased. Even if the power cord is disconnected, memory will remain

for about 2 weeks.

¢ if the memory is erased, program the presets once more.

REMOTE SENSOR window

@ | Display section

@® This lights when the front and rear balance and the rear and center

volume levels are being adjusted.

During volume adjustment

and ©) display the level, and during

balance adjustment

displays the balance.

This gives alphanumeric display of the component selected by the

INPUT SELECTOR.

When adjusting front and rear balance and volume or center volume,

this displays balance and volume level.

It also gives alphanumeric display of SLEEP when the sleep timer is

operating, and alphanumeric display of TEST when the DOLBY PRO

LOGIC SURROUND tone is ON.

@ This lights when the TAPE 2/DAT 2 monitor is ON.

® Displays the SOUND FIELD MEMORY selection.

During center or rear volume level adjustment, the volume level is

displayed.

The time remaining

when

the SLEEP TIMER

is operating

is also

displayed.

CENTER MONO OUT switch is pressed, this lights.

@ Displays the DOLBY PRO LOGIC CENTER MODE,

@) Displays the TREBLE and BASS adjustment settings.

@ Displays the selected ACOUSTIC MEMORY.

@ Lights when the VCR MONO switch is ON.

® Displays the currently selected video signal.

It also displays the video functions. If the VIDEO SELECT switch is

pressed it changes.

selected

by the VCR

1 RECORDING

SELECTOR (A component that can record to VCR 1).

@ Lights when the VCR NOISE FILTER switch is ON.

@ Displays the selected DELAY TIME.

SURROUND MODE switches/indicators

Select the source to be used when employing the SURROUND function.

OFF:

To cancel the surround function.

STUDIO:

Enjoy the atmosphere of listening to music in a recording studio.

STADIUM:

Ideal for sports broadcasts, etc.

SIMULATED SURROUND:

Gives concert-hall presence to monaural sound (AM, TV, etc.).

DOLBY PRO LOGIC SURROUND:

Select this setting when watching video tapes or video discs bearing

the

DC]

[DOLBY SURROUND | mark.