Pioneer CDJ-1000MKII Instrukcja obsługi - Strona 14

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odtwarzacz CD Pioneer CDJ-1000MKII. Pioneer CDJ-1000MKII 20 stron. Compact disc player

Drukuj stronę

ADVANCED OPERATIONS

7 Fader start play

Using the cross fader start function of the DJM-600, DJM-500, DJM-300 or

DJM-3000, step 10 above can be eliminated for even simpler mixing. In addi-

ADVANCED OPERATIONS

LOOP IN/REALTIME

LOOP OUT

CUE (IN ADJUST)

(OUT ADJUST)

HOT CUE A

HOT CUE B

HOT CUE C

HOT CUE

REC MODE

DIRECTION

FWD/REV

1, ¡

CUE

PLAY/PAUSE

Jog dial

Scratch Play (*)

By changing from the JOG MODE to VINYL, and pressing and rotating the surface

of the Jog dial you can replay according to the speed and direction of the Jog dial.

1. Press the JOG MODE SELECT button to light the [VINYL]

indicator.

2.When replaying a CD press the surface of the Jog dial.

¶ Playback slows down and stops (the slowdown in speed until the disc stops

(response characteristics) can be set separately). By rotating the Jog dial

when playback speed is decreasing but not yet stopped all sound will stop

halfway through. See Step 3 for playback when rotating the Jog dial.

3. Turn the Jog dial in the direction and at the speed you

wish to playback the disc.

¶ The CD is played back according to the speed and direction of Jog dial

movement.

4. Take your hand off the surface of the Jog dial.

¶ The CD spins up or down to return to normal playback mode.

(The slowdown or increase in speed until the CD returns to normal play-

back (response characteristics) can be set separately.)

7 Setting the time it takes for playback to slow down and

stop when the Jog dial surface is pressed.

Turn the VINYL SPEED ADJUST TOUCH/BRAKE knob.

¶ This knob allows you to adjust the slowdown in speed (response character-

istics) until CD playback stops.

7 After you have taken your hand off the surface of the Jog

dial you can set the time it takes for the speed to return

to the original condition of playback.

Turn the VINYL SPEED ADJUST RELEASE/START knob.

¶ This allows you to adjust the slowdown or increase in speed until the CD

returns to normal playback (response characteristics).

How to Spin (*)

During playback in the VINYL mode either press the surface of the Jog dial or press the

PLAY/PAUSE button (6) to cause a pause, then quickly turn the Jog dial, even

when released playback will occur according to the speed and direction of the dial.

RELOOP/EXIT

VINYL

SPEED

ADJUST

TOUCH

/BRAKE

VINYL

SPEED

ADJUST

RELEASE

/START

JOG

MODE

SELECT

tion, when the CROSS FADER slider is returned to its original position, the

status returns to that in step 9 (player CD2 at its Cue point), so that you can

repeat the same play as many times as you like.

Functions indicated with an asterisk (*) are disabled when

the rear panel DIGITAL OUT mode switch is set to NORMAL.

How to Brake (*)

¶ When you press the PLAY/PAUSE button (3/8)in the VINYL mode dur-

ing playback, the VINYL SPEED ADJUST TOUCH/BRAKE button will

cause a corresponding speed and the sound will stop.

¶ Upon pressing the PLAY/PAUSE button (3/8) again playback will com-

mence and the VINYL SPEED ADJUST RELEASE/START button will

respond accordingly.

Hot Cue (*)

Provides instant start from any of three pre-selected hot cue points (A, B or C).

7 Setting the hot cue point

1. Press the HOT CUE REC MODE button to light the HOT

CUE A, B and C button indicators in red.

2. During playback or in pause mode, press the button (A,

B or C) where you wish to store a hot cue point.

¶ The pressed button flashes for 2 seconds in red.

¶ The setting is automatically stored in the Multimedia Card (MMC).

7 Starting hot cue

1. Press the HOT CUE REC MODE button to light the HOT

CUE A, B and C button indicators in green.

¶ Buttons that do not store a hot cue point do not light.

2. During playback, in pause mode or cue standby, press

the button (A, B or C) where you stored a hot cue point.

¶ Playback starts from the stored hot cue point.

¶ Loop play is cancelled.

¶ Previously recorded hot cue points can be called from a Multimedia Card

(MMC) when a CD is inserted.

Loop Playback (*)

7 Defining a loop

1. Press the PLAY/PAUSE button (6) to begin playback.

2. During replay, press the LOOP IN/REALTIME CUE button

at the loop in point.

¶ Note that this operation need not be performed if a prerecorded Cue point is

to be used as the start of the loop.

3. During playback, press the LOOP OUT button at the point

from which you wish to end the loop.

¶ Loop playback will begin, with playback looping from the loop start point

to the loop end point.

7 Stopping loop playback

During loop playback, press the RELOOP/EXIT button.

¶ Once this has been done, playback will continue in sequence from the loop

end point without returning to the loop start point.

7 Changing the loop in point

1. Press the LOOP IN/REALTIME CUE (IN ADJUST) button

during playback.

¶ The time of the in point is shown in the display, the LOOP IN/REALTIME

CUE button starts to flash rapidly and the LOOP OUT button goes off.

2. Press the SEARCH button (1, ¡) or turn the Jog

dial.

¶ In a 1 frame unit you can move the loop in point up to ±30 frames.

¶ Press the LOOP IN/REALTIME CUE button or wait 30 seconds to leave

editing mode and return to loop play.

P.17