Pioneer CDJ-200 Instrukcja obsługi - Strona 10

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odtwarzacz CD Pioneer CDJ-200. Pioneer CDJ-200 20 stron. Compact disc player
Również dla Pioneer CDJ-200: Instrukcja obsługi (20 strony)

Drukuj stronę

OPERATIONS (DISC LOADING/UNLOADING)

DISC LOADING/UNLOADING

Label surface up

1. Set the rear-panel POWER switch to ON.

Do not force a disc into the unit when the POWER switch

is set to OFF as this may damage the disc and the unit.

2. Insert a disc.

÷ Hold the disc with label surface upwards, and insert into

the front panel disc loading slot.

÷ When playing 8 cm discs, be sure to install an adaptor.

÷ Only one disc can be loaded at a time. Never attempt to

load more than one disc at the same time, or attempt to

load a second disc when one disc has already been

loaded.

÷ When loading a disc, do not placing any twisting force

on the disc, or try to force the disc into the slot. Also, do

not attempt to interrupt or defeat the motion of the disc

when the player begins to draw a disc into the slot or to

eject a disc, since damage to the disc or player could

occur.

Forced disc ejection

If the EJECT button (0) does not function or the disc can-

not be removed, pushing the pin provided into the

forced ejection hole on the front panel will enable the

disc to be removed.

When performing forced ejection, be sure to follow the

precautions below.

1 Be sure to turn OFF the power of the CD player, and

check that the disc has stopped rotating. It takes

about 60 seconds for the disc to stop rotating after the

power has been turned OFF.

If forced ejection is performed while the disc is rotating;

÷ As the disc will be ejected outside the CD player rotat-

ing, it may hit your finger and cause injuries.

÷ As the disc will be rotating with the clamp unstable, it

may be scratched.

For the above reasons, never attempt to eject the disc

forcibly while it is rotating.

Insert straight

PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3-inch

Discs)

1 When playing CD singles (8 cm/3-inch discs), always use the

adapter for 8 cm/3-inch discs. Before loading the disc into

the CD player, be sure to check that it is secured properly by

the catches of the adapter. If discs have been inserted with-

out the adapter by mistake, remove the disc immediately by

pressing the EJECT button (0). If the disc does not come out

with one press, press another time.

2 Use 8 cm/3-inch disc adapters labeled with the

(recommended standard product). Do not use adapters

which cause the disc to idle, nor adapters which are bent or

curved.

3. Press the EJECT button (0) to remove the disc.

÷ When the EJECT button (0) is pressed, disc rotation

stops and the disc is ejected from the loading slot.

÷ If the disc cannot be ejected with the EJECT button (0),

insert a pin in the forced ejection hole on the front panel

of the player.

7 Canceling eject command

In the event the EJECT button (0) is pressed by mistake, if

the PLAY/PAUSE (6) button is pressed immediately

(before [EJECT] is displayed), the eject command will be

canceled and playback will restart from the place im-

mediately before the EJECT button (0) was pressed

(during this time, sound output will be temporarily

interrupted).

CAUTION:

Do not attempt to press a disc back into the slot when

the [EJECT] indicator appears. Pressing a disc back into

the slot while the [EJECT] indicator appears may cause

the player to stop. In this case, press the EJECT button

(0) again and wait until the [EJECT] indicator goes out

before reinserting the disc.

2 Always use the pin provided (Do not use other objects).

The provided pin is found in a groove in the bottom sur-

face of the player.

When the provided forced eject pin is inserted fully into

the forced eject hole on the front panel, the loaded disc

is ejected about 5-10 mm from the loading slot, making

it possible to remove it by hand.

mark

Forced ejection hole