AEONTEC Smart Switch 6 Podręcznik

Przeglądaj online lub pobierz pdf Podręcznik dla Jednostka sterująca AEONTEC Smart Switch 6. AEONTEC Smart Switch 6 9 stron. Low-cost z-wave switch plugin module specifically used to enable z-wave command and control (on/off) of any plug-in too

Drukuj stronę
Aeotec by Aeon Labs Smart Switch.
Aeotec Smart Switch is a low-cost Z-Wave Switch plug-
in module specifically used to enable Z-Wave command
and control (on/off) of any plug-in tool. It can report
immediate wattage consumption or kWh energy usage
over a period of time. In the event of power failure, non-
volatile memory retains all programmed information
relating to the unit's operating status.
Smart Switch 6
Its surface has a Smart RGB LED, which can be used
for indicating the output load status or strength of the
wireless signal. You can configure its indication colour
according to your favour.
View the expanded manual:
http://aeotec.com/support
The Smart Switch 6 is also a security Z-wave device and
supports Over The Air (OTA) feature for the products
firmware upgrade.
Familiarize yourself with your Smart Switch.
Quick start.
2.
If your Z-Stick is plugged into a gateway or a
computer, unplug it.
®
Getting your Smart Switch up and running is as simple
3.
Take your Z-Stick to your Smart Switch.
as plugging it into a wall socket and linking it to your
4.
Press the Action Button on your Z-Stick.
Z-Wave network. The following instructions tell you how
5.
Press the Action Button on your Smart Switch.
to link your Smart Switch to your Z-Wave network via
6.
If Smart Switch has been successfully linked to
Aeotec by Aeon Labs' Z-Stick or Minimote controller.
your Z-Wave network, its RGB LED will no longer
If you are using other products as your main Z-Wave
blink. If the inclusion was unsuccessful and the LED
controller, such as a Z-Wave gateway, please refer to
continues to blink when you press the Action Button
the part of their respective manual that tells you how add
on the Smart Switch, repeat the instructions from step
new devices to your network.
4.
7.
Press the Action Button on the Z-Stick to take it out of
When the Smart Switch is plugged
inclusion mode and then return it to your gateway or
into a wall socket and powered on,
computer.
it can act a repeater in your Z-wave
network
If you're using a Minimote:
If you're using a Z-Stick:
1.
Decide on where you want your Smart Switch to be
1. Decide on where you want your Smart Switch to be
placed and plug it in to a wall socket. Its RGB LED will
placed and plug it in to a wall outlet. Its RGB LED will
blink when you press the Action Button on the Smart
blink when you press the Action Button on the Smart
Switch.
Switch.
2.
Take your Minimote to your Smart Switch.
3.
Press the Include button on your Minimote.
Version LED indication Output (W)
4.
Press the Action Button on your Smart Switch.
Green
[0W, 1500W)
5.
If Smart Switch has been successfully linked to
EU
Yellow
[1500W, 3000W)
your Z-Wave network, its RGB LED will no longer
Red
[3000W, ∞)
blink. If the inclusion was unsuccessful and the LED
continues to blink when you press the Action Button
on the Smart Switch, repeat the instructions from step
You can also configure the brightness of RGB LED
4.
when the Smart Switch is in Energy mode, Momentary
6.
Press any button on your Minimote to take it out of
Indicate mode, or Night Light mode.
inclusion mode.
With your Smart Switch now working as a part of your
Removing your Smart Switch from a Z-Wave
smart home, you'll be able to configure it from your
network.
home control software. Please refer to your software's
Your Smart Switch can be removed from your Z-Wave
user guide for precise instructions on configuring Smart
network at any time. You'll need to use your Z-Wave
Switch to your needs.
network's main controller to do this and the following
instructions will tell you how to do this using a Aeotec
The colour of RGB LED will change according to the
by Aeon Labs' Z-Stick or Minimote controller. If you are
output load power level when it is in Energy mode:
using other products as your main Z-Wave controller,
Version LED indication Output (W)
please refer to the part of their respective manuals that
tells you how remove devices from your network.
Green
[0W, 800W)
US
Yellow
[800W, 1500W)
If you're using a Z-Stick:
Red
[1500W, ∞)
Green
[0W, 1000W)
AU
Yellow
[1000W, 2000W)
Red
[2000W, ∞)
1.
If your Z-Stick is plugged into a gateway or a
5. Press any button on your Minimote to take it out of
computer, unplug it.
removal mode.
2.
Take your Z-Stick to your Smart Switch.
3.
Press the Action Button on your Z-Stick.
4.
Press the Action Button on your Smart Switch.
Advanced functions.
5.
If your Smart Switch has been successfully removed
Changing LED mode.
from your network, its RGB LED will blink when you
press the Action Button on the Smart Switch. If the
You can change the mode of how the LED acts through
removal was unsuccessful, the RGB LED will not
configuring the Smart Switch. There are 3 different
blink.
modes: Energy mode, Momentary indicate mode, and
6.
Press the Action Button on the Z-Stick to take it out of
Night light mode.
removal mode
If you're using a Minimote:
Energy mode will allow the LED to follow the state of
the Smart Switch, when the switch is on, the LED will be
on, and while the switch is off, the LED will remain off.
Momentary indicate mode will momentarily turn the LED
on for 5 seconds then turn off after every state change
in the switch. Night light mode will allow the LED to be
turned on and off during your selected time of day you
have configured for it.
1.
Take your Minimote to your Smart Switch.
2.
Press the Remove Button on your Minimote.
Parameter 81 [1 byte dec] can be set to:
3.
Press the Action Button on your Smart Switch.
4.
If your Smart Switch has been successfully removed
(0) Energy Mode
from your network, its RGB LED will blink when you
(1) Momentary Indicate Mode
press the Action Button on the Smart Switch. If the
(2) Night Light Mode
removal was unsuccessful, the RGB LED will not
blink.