Ariston FAST EVO X ONT Instrukcje użytkownika - Strona 21
Przeglądaj online lub pobierz pdf Instrukcje użytkownika dla Podgrzewacz wody Ariston FAST EVO X ONT. Ariston FAST EVO X ONT 41 stron.
Również dla Ariston FAST EVO X ONT: Podręcznik użytkownika (42 strony), Instrukcja obsługi (12 strony)
Drukuj stronę
postavljanje
Prije postavljanja uređaja
Grijač je namijenjen za zagrijavanje vode na
temperaturu nižu od temperature vrelišta.
Mora biti spojen na sustav grijanja i na domaću mrežu
za vodu i dimenzioniran u skladu s njegovom
izvedbom, te za njegovu snagu.
Prije spajanja grijača:
pažljivo operite cijevi uređaja kako bi se uklonile
-
preostala prljavština koja bi mogla ugroziti pravilan rad
grijača;
- uvjerite se u pretpostavke grijača za rad s dostupnim
plinom
( pročitajte na etiketi ambalaže i na pločici s
karakteristikama);
- provjerite da dimnjak nije sužen i da u njega nije
spojen ispuh drugih uređaja , osim ako je dizajniran da
služi više korisnika, u skladu s odredbama važećih
propisa;
- provjerite jesu li, u slučaju spajanja na postojeće
dimne
kanale,
besprijekorno
prljavštine, moguće je da iste mogu ometati prolaz
dimnih plinova, što uzrokuje opasnost;
- provjerite je li, u slučaju montaže na neprikladnim
dimnim kanalima, da su kanalizirani;
- u prisustvu vode s posebno visokom tvrdoćom, imat
ćete rizik od kamenca što rezultira smanjenom
učinkovitošću komponenti uređaja.
Uređaji tipa B11bs su predviđeni za otvorene
prostore namijenjene za spajanje na kanal za
ispuštanje dimnih plinova koji oslobađa pare prema van;
zrak za izgaranje se odvodi izravno iz prostorije u kojoj je
instaliran uređaj.
Dimni plin se ispušta kroz prirodni ispušni sustav.
OVAJ TIP UREĐAJA NE MOŽE SE POSTAVITI U
PROSTORIJI GDJE NEMA PRIHVATLJIVIH
VENTILACIJSKIH UVJETA.
Kako normalan rad uređaja ne bi bio kompromitiran,
mjesto postavljanja mora imati pogodne temperaturne
uvjete i uređaj mora biti zaštićen na način da ne dolazi u
doticaj s atmosferskim sredstvima.
Postavljanje uređaja vrši se na čvrstom, nezapaljivom,
nepomičnom zidu kako bi se spriječio prilaz sa stražnje
strane.
Kada pripremate prostor za postavljanje, trebaju se
poštivati minimalne udaljenosti ( koje osiguravaju da se
različitim dijelovima uređaja može prići nakon
postavljanja).
21
čisti
i
ne
sadrže
installation
Before installing the appliance
The appliance heats water to a temperature below
boiling. It should be connected to a a domestic water
mains supply, that must correspond in size to the
performance and its power of the appliance.
Before connecting the appliance, it is first necessary to
perform the following operations:
- Carefully wash the system piping in order to remove
any screw thread or welding residues, or any dirt
which might prevent the appliances from operating
correctly.
- Make sure that the appliance is set up for operation
with the type of gas available (read the information on
the packaging label and on the boiler data plate).
- Make sure that there are no obstacles inside flue
exhaust and that it does not contain any discharge
from other appliances, unless the flue is meant to
serve more than one user (in accordance with current
legal requirements).
- Where there is already a connection to existing flue
exhausts, check that these exhausts have been
perfectly cleaned and are without residues, because
any disconnection could obstruct the passage of
fumes and create potentially dangerous situations.
- Make sure that, where unsuitable flue exhausts are
attached, they have been ducted.
- In areas with particularly hard water, limescale may
build up on the components inside the appliance and
reduce its overall efficiency.
B11bs-type appliances are open-chamber versions
designed to be connection to a flue gas discharge duct
which releases fumes towards the outside; combustion
air is taken directly from inside the room in which the
boiler is installed.
Flue gas is discharged through a natural draught
system.
THIS TYPE OF APPLIANCE CANNOT BE INSTALLED
IN A ROOM THAT DOES NOT MEET APPROPRIATE
VENTILATION REQUIREMENTS.
So that the normal operation of the appliance is not
compromised, the place in which it is installed must be
suitable with regard to the operating limit temperature
value and the appliance should be protected so that
it does not come into direct contact with atmospheric
agents.
The appliance must be installed on a solid, non-
combustible, permanent wall to prevent access from
the rear.
When creating a space for the boiler, the minimum
distances (which ensure that various parts of the
appliance may be accessed after it has been installed)
should be respected.