ABB ACH580 Series Skrócona instrukcja obsługi - Strona 3

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Jednostka sterująca ABB ACH580 Series. ABB ACH580 Series 15 stron. Floating point control
Również dla ABB ACH580 Series: Jak skonfigurować (2 strony)

Drukuj stronę

ABB ACH580 Series Skrócona instrukcja obsługi

EN – Quick start-up guide

This guide describes how to start-up the drive using the First start assistant on the

Hand-Off-Auto control panel. For complete information on start-up, see ACH580

firmware manual (3AXD50000027537 [English]).

EN – Quick start-up guide

Note: Automatic selection of supply voltage is not supported in ACH580-31. You must

select the supply voltage manually using parameter 95.01. See steps for

This guide describes how to start-up the drive using the First start assistant on the

Hand-Off-Auto control panel. For complete information on start-up, see ACH580 firmware

Commissioning with parameters

manual (3AXD50000027537 [English]).

Note:

Start-up with the First start assistant on an Hand-Off-Auto

Automatic selection of supply voltage is not supported in ACH580-31. You must select the

control panel

supply voltage manually using parameter 95.01. See steps for Commissioning with

parameters on page 9.

Start-up with the First start assistant on an Hand-Off-Auto

Do not start-up the drive unless you are a qualified electrician.

control panel

Read and obey the instructions in chapter Safety instructions at the beginning of the

Hardware manual of the drive. Ignoring the instructions can cause physical injury or death, or

damage to the equipment

WARNING!

Check the installation. See chapter Installation checklist in the Hardware manual of the

Do not start-up the drive unless you are a qualified electrician.

drive.

Read and obey the instructions in chapter Safety instructions at the beginning of the Hardware manual of the

Make sure there is no active start on (DI1 in factory settings, that is, HVAC default).

drive. Ignoring the instructions can cause physical injury or death, or damage to the equipment.

The drive will start up automatically at power-up if the external run command is on

Check the installation. See chapter Installation checklist in the Hardware manual of the drive.

and the drive is in the external control mode.

WARNING!

Check that the starting of the motor does not cause any danger.

The drive will start up automatically at power-up if the external run command is on and the drive

De-couple the driven machine if

is in the external control mode.

Check that the starting of the motor does not cause any danger.

• there is a risk of damage in case of an incorrect direction of rotation, or

De-couple the driven machine if

• a Normal ID run is required during the drive start-up, when the load torque is higher

• there is a risk of damage in case of an incorrect direction of rotation, or

than 20% or the machinery is not able to withstand the nominal torque transient during

• a Normal ID run is required during the drive start-up, when the load torque is higher than 20% or the

the ID run.

machinery is not able to withstand the nominal torque transient during the ID run.

The two commands at the bottom of the display (Options

The two commands at the bottom of the display

and Menu in the figure on the right), show the functions of

(Options and Menu in the figure on the right),

the two softkeys

show the functions of the two softkeys

The commands assigned to the softkeys vary depending on

the context.

located below the display. The commands

assigned to the softkeys vary depending on the

Use keys

change values depending on the active view.

context.

Key

shows a context-sensitive help page.

Use keys

For more information, see ACS-AP-x assistant control panels

and/or change values depending on the active

user's manual (3AUA0000085685 [English]).

view.

Key

shows a context-sensitive help page.

For more information, see ACX-AP-x assistant

control panels user's manual (3AUA0000085685

[English]).

on page 9.

Hints on using the assistant control panel

and

located below the display.

and

to move the cursor and/or

and

to move the cursor

Safety

and

EN – Quick start-up guide 3

R0-