Whirlpool 60-Hz Models Instrukcje instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Spryskiwacz Whirlpool 60-Hz Models. Whirlpool 60-Hz Models 5 stron. Whirlpool washer lnstallation instructions 220/240-volt, 60-hz models

Drukuj stronę

I Carefully tilt washer

backwards until front of washer is

3-4 inches (7.5-l 0 centimeters)

off of floor.

Insert piece of wood as brace.

Use legs and nuts from parts

n package.

Screw nut down to

within l/2 inch (1.3 centimeters)

of base.

Insert legs into

correct holes at

each front corner

of washer until

nuts touch washer.

Do Not tiahten nuts

until Step1 5.

Tilt washer backward

and

n remove wood block. Gently

lower washer to floor.

Move washer to its final location.

Remove cardboard

or hardboard

from under washer.

Tilt washer forward, raising

back legs 1 inch (2.5

centimeters) off of floor to adjust rear self-

leveling legs. Gently lower washer to

floor. Check levelness of the washer by

placing a carpenter's

level on top of the

washer, first side to side; then front to

back.

the front legs up or down to adjust.

Repeat Step 14.

When washer is level, use wrench

to turn nuts on front legs up tightly

against washer base. If nuts are

not tight against washer base, the

washer may vibrate.

Property Damage

Secure the drain hose to the tub or

standpipe with the shipping strap

removed from the back of the washer.

Failure to properly secure drain hose

could result in water damage.

Measure and mark a point approximately

15 inches (38.1 centimeters) from the plug

end of the shipping strap. Cut the

shipping strap at this point.

Check that hose is not twisted or

kinked and is securely in place.

Put 'hook" end of drain hose in tub or

standpipe.

Tightly wrap the shipping

strap around the drain hose and tub or

standpipe

or inlet hose as shown in

Figures A-C. Push plug into the nearest

hole in the shipping strap.

I ' ! i

' 'I_

'-1

If a longer drain hose is needed, drain

hose (Part No. 388423) and hose

extension kit (Part No. 285442) are

available from authorized parts

distributors. If drain hose must be

shortened, use hose kit (Part No. 285442).

Note: If washer

is moved

to adjust drain hose, the

washer

must be leveled

again.

Repeat

Steps 14- 15.

Place cardboard

under the washer

and carefully

move washer

to avoid

damaging

floor covering.

CHECK ELECTRICAL

REQUIREMENTS. BE SURE YOU

HAVE CORRECT ELECTRICAL SUPPLY AND

RECOMMENDED EARTHING METHOD.

n Check that all parts are now

installed. See parts list, Panel A. If there is

an extra part, go back through steps to

see which step was skipped.

Turn on water faucets and

n check for leaks. Tighten

couplings if there is leaking. DO NOT

OVERTIGHTEN; this could cause damage

to faucet.

Check that you have all of

n your tools. Check that the

shipping strap with 2 cotter pins and plug

was removed from the back of the

washer and used to secure the drain

hose.

Untape power supply cord

W and plug into earthed outlet.

Take a few minutes and

n read the Use and Care

Guide to fully understand your new

washer. Now start the washer and allow it

to complete

the regular cycle.

successfully installed

your new Whirlpool washer.

To get the most efficient use

from your new washer, read your

Whirlpool Use and Care Guide.

Congratulations!

Keep Installation Instructions and

Guide. The instructions will make

reinstalling your Whirlpool

washer in another home

Panel C