Whirlpool WASHER Instrukcja instalacji - Strona 6

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Spryskiwacz Whirlpool WASHER. Whirlpool WASHER 8 stron. Washing machine
Również dla Whirlpool WASHER: Instrukcja instalacji (16 strony), Instrukcja instalacji (27 strony), Instrukcje użytkownika (8 strony), Instrukcje użytkownika (20 strony), Instrukcje użytkownika (24 strony), Instrukcje użytkownika (8 strony), Instrukcja instalacji (20 strony), Instrukcje użytkownika (15 strony), Instrukcja obsługi i konserwacji (40 strony), Instrukcja instalacji (16 strony), Instrukcje użytkownika (8 strony), Wykres programu (2 strony), Instrukcje instalacji (5 strony)

Drukuj stronę

If drain hose does not fit into standpipe or if placing over

the edge of a laundry tub:

Insert end of coupling onto the drain hose extension. Using

pliers, install hose clamp.

Then slide the second hose clamp over end of drain hose.

Insert end of coupling onto the end of the drain hose. Using

pliers, install second hose clamp over coupling.

To prevent drain water from going back into the washer:

Do not force excess drain hose into standpipe. Hose should

be secure but loose enough to provide a gap for air.

Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose.

You may need additional parts. See Floor drain under "Tools and

Parts."

Connect the Inlet Hoses

1. Insert one new large flat washer into one end of each inlet

hose. Firmly seat the washers in the couplings.

2. Screw on the hose adapter by hand until it is seated on the

washer. Using pliers, tighten the hose adapter with an

additional two-thirds turn.

A. Inlet hose coupling

B. Large flat washer

NOTE: Do not overtighten.

3. Insert one new small flat washer into the end of the hose

adapter. Firmly seat the washers in the couplings.

Connect the inlet hoses with the adapters, to the water faucets

Make sure the washer basket is empty.

1. Attach the end of the hose with the adapter, labeled hot, to the

hot water faucet. Screw on coupling by hand until it is seated

on the washer.

2. Attach the end of the hose with the adapter, labeled cold, to

the cold water faucet. Screw on coupling by hand until it is

seated on the washer.

C. Hose adapter

D. Small flat washer

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

Tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the

valve. Damage to the valves can result.

Clear the water lines

1. Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe or bucket, to get rid of particles in the water

lines that might clog the inlet valve screens.

Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

2. Insert new large flat washers (supplied) into each end of the

inlet hoses. Firmly seat the washers in the couplings.

A. Coupling

Connect the inlet hoses to the washer

A. Cold water inlet valve

B. Hot water inlet valve

1. Attach the hot water hose to the bottom inlet valve.

2. Attaching the hot water coupling first makes it easier to

tighten connection with pliers.

B. Washer