Ariston ASL 65 VXS NA - 35140 Broszura dotycząca pielęgnacji, użytkowania i instalacji - Strona 6

Przeglądaj online lub pobierz pdf Broszura dotycząca pielęgnacji, użytkowania i instalacji dla Suszarka Ariston ASL 65 VXS NA - 35140. Ariston ASL 65 VXS NA - 35140 40 stron. Tumble dryer

Drukuj stronę

Start and Programs

The Controls

PROGRAMS knob

! Warning, if after pressing the start button, the

programs knob position has changed, the new

position will NOT change the program selected.

! Position 0, turning the knob to position 0 resets and

cancels a program, the display shows

OPTION buttons / lights

These buttons are used to customize the selected

program to your requirements. A program must have

been selected on the programs knob before an option

can be selected. Not all options are available for all

programs (see Start and Programs). If an option is not

available and you press the button, the buzzer will

beep three times. If the option is available there will

be one beep and the option light next to the button

lights to confirm the selection.

After the start button has been pressed only the

Alarm, Pre Creasecare and Post Creasecare options

can be changed.

Time Delay

The start of some programs (see Start and Programs)

can be delayed for up to 18 hours.

Press this button, the display shows

option light comes on. Press again and a 1 hour delay is

selected and the display indicates 1hr, each further press

of the button adds 1hr to the delay. When 18hr is displayed

a further press and the display shows

couple of seconds cancels the delay. You can also cancel

the delay by turning the programs knob to 0, wait for the

buzzer to beep and then turn back to your selected program.

Pre Creasecare

This option is only available if a delayed start has been

selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

High Heat

When available this button selects high heat. Press this

button and a high heat setting is selected and the light

alongside the button comes on.

Timed programs have a default of low heat, if the light

alongside the button is on then pressing the button selects

a low heat setting and the light goes out. The heat icon

on the display will also change.

Alarm

Available on all programs and allows the buzzer to give a

signal at the end of the drying cycle, to remind you that

the clothes are ready to be removed.

Press the button and the light will show that the option is

selected.

Post Creasecare

When available and selected, the clothes are occasionally

tumbled after the end of the drying and air fluff cycles,

to help prevent creases developing should you not be

available to remove the load immediately the

program is complete.

www.aristonappliances.us

OFF

and the

OFF

and after a

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for

a drying program.

The delay time is displayed in hours and counts down

each hour.

The time to end is displayed in hours and minutes and

counts down each minute, this time includes the air

fluff phase. When timed programs are selected the

time displayed throughout the cycle is the actual time

remaining.

When a sensing program is selected the time

displayed is an estimate of the time remaining. When

the program is selected the display shows the time

required to dry a full load, after around 10 minutes the

controller calculates a better estimate of the cycle

time.

The colons between the hours and minutes in the

display flash to show that the time is counting down.

When the program finishes its air fluff phase the

E88

display will show

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

Door Opening

Opening the door during a program will stop the dryer

and have the following effects:

All 4 progress lights come on.

During a delay phase the delay will continue

to count down. The start button must be

pressed to resume the delay program.

The progress lights will change to show

current status.

During the drying part of the program, the

time to end count continues but the colons

do not flash. The start button must be

pressed to resume the program. The progress

lights will change to show the current status.

During the air fluff or post creasecare phase

of a drying program and anytime during an

Airing or Air fluff program, the program will

finish. Pressing the start button will re-start a

new program at the beginning.

Changing the programs knob will select a new

program, after you press the start button. You

can use this to select the Air Fluff program to

cool the clothes, if you find them dry enough.

Note

If you have a power outage, switch off the power or

remove the plug, press the START button and the

program will resume.